RXSOL - Sewage Chemicals Treatment-40

RXSOL-16-2066-210 is antifoam emulsion and its more concentrated antifoam emulsion. It has excellent candidates for controlling foam in amine and glycol dehydration units. This is suitable products for gas plants and have excellent stability in the presence of salts, resulting in reduced deposits on the plant’s equipment. RXSOL-16-2066-210 help preserves foam control under the severe conditions of a dehydrating unit. These conditions can remove water from other antifoam emulsions, rendering them immediately inactive.

Alias:

BELITE M-8 / ANTISPUMIN DS (ANTI FOAM)

Application:

This antifoam compound are targeted for gas recovery plants, where natural gas must be washed, or scrubbed, before distribution, and for liquefied natural gas (LNG) plants that must achieve high gas purity before liquefaction.

In many amine units, foam can be problematic. Proper line control without antifoam is, generally, extremely difficult.

General-purpose antifoams have a wide range of applicability, but not all of them are suitable for use in the treatment of gas. Some foam control agents can aggravate the problem. Foam control in gas scrubbers is only one of the process parameters to be monitored. It is equally important to prevent or slow the fouling of the unit, because dismantling of the gas-scrubbing units is manually intensive. Incorrectly specified antifoams can easily lead to increased fouling and clogging, particularly in the heat exchangers. Momentive Performance Materials RXSOL antifoams are designed to provide foam control with a minimum of such problems.

Packing Size:

210.00 Ltr.

Image:

Thumb:

Note:

Key Features and Benefits

Quick foam knockdown - particularly useful when foam suddenly builds up in the absorber and rapid control is needed.
Excellent antifoarn stability and durability - over a period of time the concentration of salts in an amine or glycol dehydration unit can reach high levels. RXSOL-16-2066-210 antifoam emulsion and its more concentrated version, are easily dispersed in water and are compatible with glycols, they do not allow the presence of these glycols to easily remove water from their state of emulsion, thus remaining effective for a longer period.
Excellent stability at high temperatures - because of their excellent dispersibility. RXSOL-16-2066-210 antifoam emulsion do not show a propensity to deposit on heat exchangers as many other antifoams tend to. Instead, they remain finely dispersed in the amine or glycol solution and are eventually filtered out.
Easy dilution and use - simple addition of water and minimum agitation is sufficient to dilute RXSOL-16-2066-210 antifoam emulsion to required concentrations. Pumping of the diluted emulsions is easy, due to their low viscosity.
Reduced clogging or scaling in the heat exchangers - potentially resulting in less service maintenance.
Low concentrations can provide effective foam control - RXSOL-16-2066-210 antifoam emulsion and often two to three times more effective than other antifoams used in gas treating units.

Product Safety, Handling and Storage

Customers should review the latest Material Safety Data Sheet (MSDS) and label for product safety information, safe handling instructions, personal protective equipment if necessary, and any special storage conditions required for safety. MSDS are available at www.rxmarine.com or, upon request, from any RX MARINE INTERNATIONAL representative. For product storage and handling procedures to maintain the product quality within our stated specifications, please review Certificates of Analysis, which are available in the Order Center.

Featured Product :

Featured Product

Article News:

Oil Filed Maintenance Chemicals

Short Description:

RXSOL-16-2066 is antifoam emulsion and its more concentrated antifoam emulsion. It has excellent candidates for controlling foam in amine and glycol dehydration units. This is suitable products for gas plants and have excellent stability in the presence

Antifoam emulsion

Sodium Thiosulfate commonly used in Dechlorination of municipal wastewater, pulp & paper, power, and textile water treatment plants and as an Oxygen scavenger in oil well drilling process in Mining industries.

Alias:

Chlorine control, Declor-it, Disodium thiosulfate, S-hydril, Sodium hyposulfite, Sodium oxide sulfide, Antichlor, Sodothiol, Sulfothiorine, Ametox

Active Matter:

48-50

Application:

Dechlorination in municipal, pulp & paper, power, and textile water treatment plants, Oxygen scavenger – oil well drilling process Mining industries Aluminum cation reaction

Industrial production and laboratory synthesis

On an industrial scale, sodium thiosulphate is produced chiefly from liquid waste products of sodium sulphide or sulphur dye manufacture.In the laboratory, this salt can be prepared by heating an aqueous solution of sodium sulphite with sulphur.

Principal reactions and applications

Thiosulfate anion characteristically reacts with dilute acids to produce sulfur, sulfur dioxide and water-

1.Na2S2O3 + 2HCl →2NaCl + S + SO2 + H2O

This reaction is known as a "clock reaction", because when the sulfur reaches a certain concentration the solution turns from colourless to a pale yellow. This reaction has been employed to generate colloidal sulfur. When the protonation is conducted at low temperatures, H2S2O3 (thiosulfuric acid) can be obtained. It is a somewhat strong acid with pKas of 0.6 and 1.7 for the first and second dissociation respectively.

Iodometry

In analytical chemistry, the most important use comes from the fact that the thiosulfate anion reacts stoichiometrically with iodine, reducing it to iodide as it is oxidized to tetrathionate:

Photographic processing

The terminal sulfur atom in S2O32− binds to soft metals with high affinity. Thus, silver halides, e.g. AgBr, typical components of photographic emulsions, dissolve upon treatment with aqueous thiosulfate:

2 S2O32− + AgBr →[Ag(S2O3)2]3−+ Br−

In this application to photographic processing, discovered by John Herschel and used for both film and photographic paper processing, the sodium thiosulfate is known as a photographic fixer, and is often referred to as hypo, from the original chemical name, hyposulphite of soda.

Gold extraction

Sodium thiosulfate is one component of an alternative lixiviant to cyanide for extraction of gold.[3] It forms a strong complex with gold(I) ions, [Au(S2O3)2]3−. The advantage of this approach is th

2 S2O32−(aq) + I2(aq) →S4O62−(aq) + 2 I−(aq)

Due to the quantitative nature of this reaction, as well as the fact that Na2S2O3•5H2O has an excellent shelf-life, it is used as a titrant in iodometry. Na2S2O3•5H2O is also a component of iodine clock experiments.

This particular use can be set up to measure the oxygen content of water through a long series of reactions. It is also used in estimating volumetrically the concentrations of certain compounds in solution (hydrogen peroxide, for instance) and in estimating the chlorine content in commercial bleaching powder and water.at thiosulfate is essentially non-toxic and that ore types that are refractory to gold cyanidation (e.g. carbonaceous or Carlin type ores) can be leached by thiosulfate. Some problems with this alternative process include the high consumption of thiosulfate, and the lack of a suitable recovery technique, since [Au(S2O3)2]3− does not adsorb to activated carbon, which is the standard technique used in gold cyanidation to separate the gold complex from the ore slurry.

Packing Size:

25.00 Ltr.

Image:

Thumb:

Using Procedure:

Process for DE CHLORINATION :::

Take 500 ml of Sodium Thiosulfate stock solution.

Add two drops of the stock solution per one gallon of the water to be treated.
One gallon can treat 37,850 gallons or more. Over-dosage is virtually impossible.

Note:

Analytical chemistry

Sodium thiosulfate is also used in analytical chemistry. It can, when heated with a sample containing aluminum cation, produce a white precipitation:

2 Al3+ + 3 S2O32− + 3 H2O →3 SO2 + 3 S + 2 Al(OH)3

Medical

It is used as an antidote to cyanide poisoning. Thiosulfate acts as a sulfur donor for the conversion of cyanide to thiocyanate (which can then be safely excreted in the urine), catalyzed by the enzyme rhodanase.

It has also been used as treatment of calciphylaxis in hemodialysis patients with end-stage renal disease.[6]

It is used in the management of extravasations during chemotherapy. Sodium thiosulfate prevents alkylation and tissue destruction by providing a substrate for the alkylating agents that have invaded the subcutaneous tissues. The dose may be 2mL of 0.17M (a solution of 4mL 10% sodium thiosulfate and 6mL sterile water for injection). It may be instilled subcutaneously into multiple sites using a small gauge needle. There is limited data on this method with few recommendations.

in foot baths for prophylaxis of ringworm, and as a topical antifungal agent for tinea versicolor.

in measuring the volume of extracellular body fluid and the renal glomerular filtration rate.

Sodium thiosulfate is also used:

As a component in hand warmers and other chemical heating pads that produce heat by exothermic crystallization of a supercooled solution.

In bleach

In pH testing of bleach substances. The universal indicator and any other liquid pH indicators are destroyed by bleach, rendering them useless for testing the pH. If one first adds sodium thiosulfate to such solutions, it will neutralize the color-removing effects of bleach and allow one to test the pH of bleach solutions with liquid indicators. The relevant reaction is akin to the iodine reaction: thiosulfate reduces the hypochlorite (active ingredient in bleach) and in so doing becomes oxidized to sulfate. The complete reaction is:

4 NaClO + Na2S2O3 + 2 NaOH →4 NaCl + 2 Na2SO4 + H2O

To dechlorinate tap water for aquariums or treat effluent from waste water treatments prior to release into rivers. The reduction reaction is analogous to the iodine reduction reaction. Treatment of tap water requires between 0.1 grams and 0.3 grams of pentahydrated (crystalline) sodium thiosulfate per 10 liters of water.

To lower chlorine levels in swimming pools and spas following super chlorination.

To remove iodine stains, e.g. after the explosion of nitrogen triiodide.

Similarly, sodium thiosulfate reacts with bromine to render harmless products. Solutions of sodium thiosulfate are commonly used as a precaution in chemistry laboratories when working with bromine.

In bacteriological water assessment.

In the tanning of leather.

To demonstrate the concept of reaction rate in chemistry classes. The thiosulfate ion can decompose into the sulfite ion and a colloidal suspension of sulfur, which is opaque. The equation for this acid-catalysed reaction is as follows:

S2O32−(aq) →SO32−(aq) + S(s)

To demonstrate the concept of supercooling in physics classes. Melted sodium thiosulfate is very easy to overcool to room temperature and when crystallization is forced, the sudden temperature jump to 48.3 °C can be experienced by touch.

As part of patina recipes for copper alloys.

Often used in pharmaceutical preparations as an anionic surfactant to aid in dispersion.

It can also be used as a very interesting solute in supersaturation experiments.

Short Description:

Sodium Thiosulfate used as a Pond / Aquarium Dechlorinator. This product also used as a Photography as a fixing agent (hypo) to dissolve unchanged silver salts from exposed negatives.

Sodium Thiosulfate Solution (Na2S2O3) suitable for Dechlorination in municipal wastewater, power, and textile, marine, Industrial pulp & paper water treatment plants.
Sodium Thiosulfate Solution also used as Oxygen scavenger – oil well drilling process. Mining industries. Aluminium cation reaction etc...

Dechlorinating liquid

Air Cooler Cleaner Sea Water SIDE is specialized product to dissolve water scale smoothely. We are manufacturer and supplier of Air Cooler Cleaner Sea Water SIDE.

Alias:

De-scalex (Liquid), YUNISOL X, Safe Acid Descalex Liquid.

Application:

RXSOL-54-1048-020 is mixed with fresh water 3 to 20 percent depending on deposition of scaling.

If the equipment to be cleaned is contaminated by oil, grease, sludge or carbonized oil, then first of all clean the system with degreaser RXSOL-10-1005. RXSOL-54-1048-020 should be mixed with fresh water to form a solution of 10-30%, depending on the extent of scaling. After using RXSOL-54-1048-020 ,

PRECAUTION :::it is essential to thoroughly rinse all metal surfaces at least once with a 0.5% solution of RXSO-20-2005 in fresh water. This solution should be circulated for 2-4 hours or until an acceptable pH value is obtained. This will neutralize any remaining acidity & passivate steel surfaces.

Procedure-of-use: The most effective descaling is accomplished by circulation.In the case of small components,the soak method in an immersion bath can be used. If the equipment to be cleaned is contaminated by oil, grease or sludge, then pre-cleaning with DEGREASER ( RXSOL OB 1005 ) is necessary. Depending on the extent of scaling, use a solution of 2.5-10% RXSOL-54-1008-025 . The solution will have a red colour which changes to orange when 85% of the acid has been neutralized , & to colourless when the solution is totally neutralized. Whenever possible, the solution should be heated to 60°C.Neutralised solutions can be re-activated by adding more RXSOL-54-1008-025 until the red colour reappears.

Fields: Descaling of Boilers, Descaling of Diesel Engine Cooling Systems, Condenser, Pipeline collection system, Evaporators, Calorifiers, Heat Exchangers,The strength of the acid can be enhanced by adding 1part sodium chloride (common salt) to 20 parts of Descalex.If salt is not available, an acceptable alternative is to dissolve RXSOL-54-1008-025 in sea water. After use of RXSOL-54-1008-025 a 0.5% solution of Alkalinity Control in fresh water should be used for neutralization.

Packing Size:

25.00 Ltr.

Image:

Thumb:

Using Procedure:

After using RXSOL-54-1048-020, sense all metal surfaces with 0.5 percent of RXSOL-10-1005, at least 2-4 hour , up to neutral of PH value.

• Fast and effective scale remover.
• Soft on ferrous metals.
• Removes water scale & rust from boilers/diesel engine & other cooling system
• As well as from condensers, evaporators, & heat exchangers etc

Why Use RXSOL Descaler?

It is a safe , economical concentrated chemical to be used on the waterside of heat transfer equipment.
You do not have to heat RXSOL-54-1048-020 .
RXSOL-54-1048-020 is safer for the employees to use than other acid products.
Your equipment will be cleaned in only hours without disassembling any part of the equipment. Equipment can also be cleaned without any down time (cleaning on the run).
Cleans down to the original surface without pitting.
RXSOL-54-1048-020 is safe on copper, copper-nickel, bronze, brass, iron, stainless steel and rubber.
RXSOL-54-1048-020 will extend the usable life of your equipment, especially when used as a part of a regularly scheduled preventative maintenance program.
Removing the scale build up allows your equipment to operate more efficiently with less down time.

Note:

• Automotive - Closed Circuit Cooling, Dynamometers, Extruders, Molders, Radiators, Welders

• Bottling - CO2 Generators, Heaters, Exchangers, Rinse Tanks, Sterilizers, Washers

. HOUSE HOLD - Dissolves hard and old lime scale deposits from your appliances. It extends the life of the appliance and saves running cost. It can be used in appliances such as Washing Machines, Dish Washers, Geysers, Steam Iron, Coffee Makers, Bath Tubs, Bathroom Fixtures etc.

• Buildings - Chillers, Cooling Towers, Pipework

• Chemicals - Dryers, Extruders, Kettles, Mixers, Reactors, Scrubbers, Vacuum Pumps

• Food - Condensers, Ice Machines, Kathabars, Refrigeration Equipment, Steam Tables

• Manufacturing - Chillers, Compressors, Furnaces, Quenchers, Vacuum Pumps

• Metals - Bearings, Castings, Fans, Hearth & Vacuum Furnaces, Shelters, Sprays

• Mining - Bearings, Conveyors, Filters, Presses, Process Lines, Radiators

• Paper- Calendar Mill Rolls, Caustic Lines, Scrubbers, Compressors, Liquor Tanks, Pulverizers, Vacuum Pumps

• Pharmaceutical- Exchangers, Loop Systems, Kathabars, Pumps, Reactors, Stills, Sterilizers

• Refinery - Compressors, Converters, Crackers, Exchangers, Piping, Pumps

• Rubber/Plastics - Banbury Mixers, Calendar & Mill Rolls, Extruders, Injection Molders, Molds, Temperature Control Units, Throat Coolers, Towers, Tubers

• Steel - Bearings, ConCast Units, Generators, Hearths, Spangle Units, Furnaces

• Textile - Air Washers,Compressors, Condensers, Exchangers, Extruders,Towers

Boilers

Condensers

Filters

Heat Exchangers

Kettles & Tanks

Pipelines

Pots

Reactors

Steam Jackets

Bath Rooms and Showers

Metal Processing and much more!

Applications

Automotive	Bottling	Chemicals	Food
- Closed Circuit Cooling - Dynamometers - Extruders - Molders - Radiators - Welders	- CO2 Generators - Heaters - Exchangers - Rinse Tanks - Sterilizers and Washers	- Dryers - Extruders - Kettles - Mixers - Reactors - Scrubbers - Vacuum Pumps	- Condensers - Ice Machines - Kathabars - Refrigeration Equipment - Steam Tables
Manufacturing	Metals	Mining	Paper
- Chillers - Compressors - Furnaces - Quenchers - Vacuum Pumps	- Bearings - Conveyors - Fans - Hearth & Vacuum Furnaces - Shelters - Sprays	- Bearings - Conveyors - Filters - Presses - Process Lines - Radiators	- Calendar Rolls - Mill Rolls - Caustic Lines - Scrubbers - Compressors - Liquor Tanks - Pulverizers - Vacuum Pumps
Pharmaceutical	Refinery	Rubber & Plastics	Steel
- Exchangers - Loop Systems - Kathabars - Pumps - Reactors - Stills - Sterilizers	- Compressors - Converters - Crackers - Exchangers - Piping - Pumps	- Banbury Mixers - Calendar & Mill Rolls - Extruders - Injection Molders - Molds - Temperature Control - Units - Throat Coolers - Towers and Tubers	Bearings ConCast Units Generators Hearths Spangle Units Furnaces
Textile	Utilities	Other Applications
- Air Washers - Compressors - Condensers - Exchangers - Extruders and Towers	- Boilers - Turbines - Transformers - Cooling Towers - Air Compressors - Hydrogen Coolers - Lube Oil Heat Exchangers	- Ball Mills - Demisters - Evaporators - Locomotives - Absorption Units - Diesel Generators - Induction Furnaces

Related Products:

Air Cooler Cleaner 25 Ltr

Air Cooler Cleaner LT 25 Ltr

Air Cooler Cleaner Plus 25 Ltr

Air Cooler Cleaner Alkaline 25 Ltrs

Coil Brite Rx Yellow

Coil Brite Rx PINK

Evaporator Coil Cleaner

Condenser Coil Cleaner

Safety Accessories:

Hand Gloves Chemical resistance

Goggle Chemical Protective

Featured Product :

Featured Product

Short Description:

De-scalex Liquid for AIR COOLER WATER side.

Dirt in tubes of seawater side

White scales attached on the seawater side of air coolers of many vessels. We found that in most cases, the main component of the scales is calcium carbonate and there is also a small amount of calcium sulfate. Therefore in most cases, if you dissolve the calcium carbonate the scales will be removed.

However, if the amount of scales is large enough to block the tube, the cylindrical scale will usually have calcium carbonate on the outside (the side that is in contact with tube) and calcium sulfate in the center (part that seawater passes through). Calcium sulfate is easier to be formed when the temperature goes higher.

When the amount of scales increases, the contact area of scale and cleaner is very small and a longer time of dissolution is required. Calcium sulfate cannot be dissolved by an acid cleaner.

RXSOL-54-1048-020 is a powerful dissolving agent of calcium carbonate. Therefore, it is better to use RXSOL-54-1048-020 to do circulating cleaning at an early stage before the scales build up and block the tube, or regular cleaning is recommended as well. It is impossible to do a circulating cleaning when the tube is completely blocked.

while Dirt attached on air-side fins of air coolers are a mix of carbonaceous particles such as soot and oil mist of unburned fuel components can be clean by RXSOL-16-0009-025. ( www.rxmarine.com/air-cooler-cleaner-25-ltr )
Carbonaceous particles can be removed by alkaline cleaners and oil mist can be removed by oil based cleaners. However, it is very difficult to remove the mix of these substances. If you use an alkaline cleaner, oil will repel the water based alkaline cleaner; if you use oil based cleaner, carbonaceous particles will get in the way and stop oil from being removed.

This cleaners designed to remove both carbonaceous and oil simultaneously. An effective cleaning method is to immerse one side to remove the loose stains first, and then immerse the other side. This method can efficiently remove dirt and prevent swollen dirt peeled from fins from blocking the spaces between fins.

Also Suitable for Cleaning of BOILER and Cooling Water deposition...

Scales are very damaging to the boiler because they interfere with the heat transfer and can lead to overheating and eventually, boiler rupture , To increas usable life of cleaned equipment , it is safe and effective way to remove scale deposits from all types of water-cooled and water-heated equipment. This descaler specifically formulated and developed to rapidly clean mineral scale from passages in water-cooled or heated equipment. It improves Plant Efficiency, Lowers Cost, Conserves Energy, Decreases Down-Time.

Chemically react with and decompose Calcium, Magnesium deposited Salts. Suitable for pipeline, boiler, HVAC, Heat Exhanger, Condenser, Evapourator, Chiller, Compressor and etc. Specifically formulated to remove rust and water scale build up from boiler evaporators, heat exchangers, cooling systems, pipeline collection system etc. Highly effective on heating. Safe and easy handling and storage . Fast and effctive scale remover .

-   Non-combustible
-   Smoke from fires is irritating
-   Not flammable. In case of fire use extinguishing media appropriate to surrounding conditions
-   Prevent run off water from entering drains if possible
- Non-poisonous ::: It does not contain toxic cresols or other tar oils that Require SARA Title III, Section 313 spill loss or disposal.
Non-polluting, Non-corrosive.

Uniqueness of RXSOL-54-1048-020 ::: ---
RXSOL-54-1048-020 Descaler has the ability to dissolve approximately 1.5kg of calcium carbonate scale per gallon in concentrated form. It does not need to be heated up during cleaning. The uniqueness of this Descaler allows you to clean some equipment while still in operation utilizing a minimum of your own personnel.

RXSOL 2000 Ltr is a unique formulation with organic Engine Corrosion Inhibitors , Anti-Scalant for use in closed cooling water systems , as a high temperature coolant for internal combustion stationers, engines, machinery, snow melting systems, industrial heat transfer fluids, for preventing corrosion and scale Formation in Internal combustion engines, compressor cooling system, DG -set at high or low temperature. It is a concentrated liquid , also used as a corrosion inhibitor and protects all the metals including cast iron , mild steel , copper .

Alias:

NALFLEET Nalcool 2000 PART-777710, Rodine 231, Rodine 234, Rodine 244, INDION 5547

Active Matter:

45 - 54

Application:

Application: All types of Engine Jackets, Radiator and Engine coolant.
The stable oxide film that is formed by RXSOL 2000-II prevents corrosion caused by electrolytic action between dissimilar metals used in the system . RXSOL 2000-II has been field tested and found to have no detrimental effects on non metallic substances such as seals, glands, packing, hoses, gaskets etc., normally used in these’ systems.

Application-Dg*

Sets Internal combustion engines closed circuit cooling system compressor cooling system. Rxsol 2000-II incorporates superior corrosion inhibitors to prevent corrosion works by free of scale deposits.

Advatages: -

1. Prolong the life of equipment by keeping scale and corrosion free. Since RXSOL 2000-25 Ltr is alkaline and so will suppress acid corrosion, which would otherwise result in corrosion damage such as pitting. However, the alkalinity control is such that even if the product is accidentally overdosed, the pH of the water will remain within limits. The metals which would be affected by extremes of alkalinity or acidity are protected. protect cast iron diesel engine cooling systems.

2. Improves generating cooling efficiency by maintaining a clean heat transfer by protect against sludge and mineral scale formation.

3. Corrosion protection by using superior corrosion inhibitor.

4. Reduced maintenance and down time

5. Compatible with Coolants / Antifreeze solution / Glycol .

6. Friendly with Metals (Like steel, Copper, Aluminum, all alloys) & Non-metal (Rubber, Hoses, Gasket , and ‘O’rings.etc.)

7. Prevents over heating Effective against liner pitting and cavitation erosion.

NOTE :::
•Protects both ferrous and non-ferrous metals from oxygen & corrosion.
•Compatible with most coolants and anti frizzles.
•Non staining.

Packing Size:

25.00 Ltr.

Image:

Thumb:

Using Procedure:

Initial dosage for an untreated system is 9 litres of RXSOL 2000-II / 1000 litres of untreated distilled water. This will bring the treatment up to the minimum level of 1000 ppm nitrite. For best result and prolonged engine life add RXSOL 2000-I every 500 -6500 km. or 250 to 300 hours of running time or every 2 month interval .

Note:

In cases where systems are contaminated with oil and/or scale they should be cleaned before starting to apply RXSOL 2000 .There are suitable RX BRAND products to carry out the cleaning. Degreasing should be carried out using RXSOL 2000-II and descaling by using RXSOL 2000-II.

SPECIFICATION / HANDLING
Color                           : Odour Pink/ red (Colour changes of the product can not be excluded the effectively will however not impaired.)
Sp. Gravity                  : 1.1 to 1.25
pH                              : Alkaline (11.3 – 11.5)
None. Rxsol-2000 is an alkaline product & should be handled like other chemical Avoid contact with Eyes, Skin ,in case of contact ,wash with copious amounts of water immediately.
Freezing Point - 17 0 c
Nitrite (as PPM NO2)       0                   100-200      300-600        700-900      1100-1300    1440-2400
RXSOL 2000 /1000L      13.0               11.3    8-10       5-7               1.5-3.5    0

METHOD OF USE
1. Properly clean the system with water and alkaline liquid , if necessary.
2. Add 0 .15-1.5 % of Rxsol -2000 in system or recommended Nitrite level 1400 – 2500 ppm can be measured and controlled by any standard RXSOL test kit for Nitrite, Chloride test also helps to detect excess contamination to maintain accepted levels . when the product is dosed as recommended limit By buffering action of RXSOL - 2000 , pH should be maintained between 8.3 and 10 by the treatment.

NOTE ::: Engine cooling system should be drained, flushed and if necessary chemically cleaned with (Aluminum & Metal Cleaner) for to remove old rust and scale deposits, before treatment with RXSOL 2000 .

Featured Product :

Featured Product

Article News:

Rocor NB cooling water treatment chemicals

Short Description:

Engine Corrosion Inhibitors and anti scalant which is effective against liner pitting and cavitation erosion. It prevents over heating of engine and thus reducing chances of shut down. It is non-harmful to radiator or heater connecting hoses, diesel liner seals and ‘O’ rings.

RXSOL 2000 corrosion inhibitor manufacturer, supplier and exporter in India and Middle East.

Engine Corrosion Inhibitors

FAQ:

Why Rocor NB Liquid?

COOLING WATER CORROSION & SCALE INHIBITOR

Alias:

DEWT NC, Liquid EWT, Cooltreat, Nalco 2000 , Cwt Nclt diesel, Liqui guard 2000, ENGINE JACKET WATER CONDITIONER , Gyrocor W.C., Aquafine 103, CWT-NT Chemo, NCT-105 L Norchem, DM-521, DWT 444, EAZY CWT-DE, 653-571356, Caretreat 2 Diesel, Coronil 202<

Active Matter:

68 - 75

Application:

Prolongs the life of equipment by keeping it scale and corrosion free. Since RXSOL-40-4001-025 is alkaline, it will suppress acid corrosion, which would otherwise result in sever pittings. It improves cooling efficiency by maintaining clean heat transfer surfaces , from Radiators, DG - sets, Closed Cooling and chiller System.

FIELDS ::: --- Suitable for use in closed water cooling systems, ice melting systems and transformer cooling systems. The product may be used in all kinds of diesel & petrol engines, compressor or heating cooling water circuits.

( Used as a corrosion inhibitor for all ferrous and non-ferrous metals found in water systems )

Packing Size:

25.00 Ltr.

Image:

Thumb:

Using Procedure:

Refer to technical datasheet.

GENERAL RECOMMENDATION : ( The dosage chart may be used as a guide to adjust treatment to obtain the optimum level.)

Nitrite (as PPM NO2)	0	100-200	300-600	700-900	1100-1300
RXSOL-40-4001-025 / 1000L	8.0	7.3	7-8	5-7	1.5-3.5

NOTE ::: -- If nitrite level becomes 1440-2400 then doses should be ZERO.

The initial dosage for an untreated system is 8 liters of product per 1000 liters of water. Such a dose will bring nitrite levels over 1200 ppm. Maximum nitrite level is considered to be 2400 ppm. Frequent tests should be carried out in order to maintain pH values within the limit (8.3-10.0), while levels of chloride should be maximum 50 ppm.

Note:

Initial dosage for an untreated system is 9 litres of RXSOL-40-4001-025 / 1000 litres of untreated distilled water. This will bring the treatment up to the minimum level of 1000 ppm nitrite. For best result and prolonged engine life add RXSOL-40-4001-025 every 500 -6500 km. or 250 to 300 hours of running time or every 2 month interval. Specially designed for use in water systems of internal combustion equipment. pH should be maintained between 8.3 and 10 by the treatment.

RXSOL-40-4001-025 will react with sludge and in most cases, facilitate sludge gradual removal. On badly fouled systems with oil or scale, a prior degreasing by using DEGREASER HEAVY DUTY or descaling by using DEGREASER HEAVY DUTY, SCALE REMOVER LIQUID or SCALE REMOVER POWDER is highly recommended.

• Excellent corrosion inhibitor for cooling water

• Minimises metal oxide deposits

• Protects ferrous and non-ferrous metals

• Compatible with glycol-based antifreeze

• Reduces cleaning & maintenance costs

• Cost effective, easy to apply and use

Related Products:

Sodium Molybdate 35%

Antifreeze with Potassium Chromate

Diesel Guard NB Pwd ( Rust Scale Inhibitor ) DEWT

RXSOL 2000 corrosion inhibitor

Safety Accessories:

Hand Gloves Chemical resistance

Goggle Chemical Protective

Featured Product :

Featured Product

Article News:

Corrosion inhibitors types for closed cooling water systems

Molybdate and Rocor NB comparison

Why Biological Guard Antifouling required with Rocor NB liquid ?

Oil Filed Maintenance Chemicals

Borax as a corrosion inhibitor

Marine Chemicals supplier

Why Marine Chemicals?

Rocor NB cooling water treatment chemicals

Short Description:

Unique formulation with highly concentrated liquid cooling treatment compound, ferrous & Non ferrous corrosion inhibitors, antiscalants , dispersant and buffer solution of non carbonate.Usefull for use in high or low temperature closed cooling water syste

Information:

ROCOR NB liquid is one of popular cooling water treatment chemical. This product contains nitrite and borate as major component along with new generation corrosion inhibitor which makes new advance ROCOR NB then others. Many experiment proves that water of closed cooling system required special treatment to prevent pitting corrosion and scale formation. Special Blend of Nitrite and Borate with watersoftening polymer plays excellent role in cooling system.

The closed cooling system uses the water flowing through a heat exchanger to remove heat from the engines. If Continuous flow of cooling water contains Rocor Nb corrosion inhibitor and antifreeze mixture resulting good protect towards metal surface.

ROCOR NB liquid msds and technical bulletine available here.
ROCOR NB is one of classified corrosion inihibitor for cooling water system. Ferrous and Non ferrous metal parts of cooling water system gets corrosion and changes into pitting formation which results in the form of leakage and many more. But presence of balance level of nitrite and borax which is main compenent of ROCOR NB Liquid, effectively control corrosion on metal surface, This is the reason why uses of ROCOR NB liquid is most common in COOLING WATER SYSTEM on the other hand we can say that ROCOR NB Liquid is the ideal corrosion inhibitor for closed heating or cooling systems, such as diesel engines, compressors, process cooling systems, etc.

Also refer this link http://rxmarine.com/engine-water-treatment-corrosion-inhibitor

During Circulation of water mainly controlling of 2 factors required : -

SCALE CONTROL in closed water cooling systems - Diesel and gas engines releasing high temperature due to that water present in jacket cooling system increases its tendency to deposit scale. To avoid scale formation water softener like Zeolite gradual buildup of scale in cylinders and cylinder heads. Where condensate is available, it is preferred for closed system cooling water makeup. Where condensate is not available, zeolite softening should be applied to the makeup water.

CORROSION CONTROL An increase in water temperature causes an increase in corrosion. At high temperature solubility of oxygen in water decreases due to that Corrosion rates increasing inside the system. This occurs because the lower solubility of oxygen with increasing temperatures in a freely vented system decreases the corrosion rate faster than the rise in temperature increases it. However, in many closed systems, the dissolved oxygen entering the system in the makeup water cannot be freely vented, resulting in the release of oxygen at points of high heat transfer, which may cause severe corrosion. Untreated systems can suffer serious corrosion damage from oxygen pitting, galvanic action, and crevice attack. Closed cooling systems that are shut down periodically are subjected to water temperatures that may vary from ambient to 180°F (82°C) or higher. During shutdown, oxygen can enter the water until its saturation limit is reached. When the system is returned to high-temperature operation, oxygen solubility drops and the released oxygen attacks metal surfaces.

The three most reliable corrosion inhibitors for closed cooling water systems are chromate, molybdate, and nitrite materials. Generally, the chromate or molybdate types have proven to be superior treatments.

What is closed cooling system ?
The full closed cooling system is designed to circulate cooling water through the block and exhaust manifold. water is circulated through water pump to heat exchanger tank and be pumped through many small tubes where it will exchange heat from the water of the circulating system. Then water exits the heat exchanger to go directly into the risers and then exit the boat. The exhaust manifold and riser will be blocked off, so no water will transfer between them. As for the circulating water in the closed cooling system, cool water will enter the engine through the circulating pump and circulate through the engine. The water will heat up in the engine and the warm water will exit at the water outlet on top of the manifold and head to the manifolds. After circulating through the manifolds, the hot water will head to the heat exchanger to exchange the heat it's carrying with the raw water. After the exchange the cool circulating water exits the heat exchanger and returns to circulating pump to begin another loop.

Closed cooling system corrosion inhibitor

FAQ:

Nitrite Level 1200 to 2000 ppm

Foul dirty cooling water treatment chemical

Why Rocor NB Liquid?

Extremely high quality. It is produced by means specialist piece of equipment to produce it called a demineralisation plant or a deionisation plant. After completion of chemical treatment .

The incoming water passes over a series of SPECIALIZED RESIN BEADS which remove mineral ions and other impurities from the water. This is why Demineralised Water is also known as Deionised Water; the process removes minerals and ions leaving water which is de-mineralised or de-ionised. Demineralised Water is also known as Demin Water, DI Water and DIW.

Alias:

D.M.Water, demineralized, DM water

Application:

This type of water is routinely used for:-

Laboratory applications such as autoclaves and laboratory testing
Automotive cooling systems
‘Lead-acid’ type vehicle batteries
Laser cutting
Steam irons
Aquariums
Humidifiers
Cosmetics (where the word ‘aqua’ appears on an ingredients list it often refers to Demineralised Water)
Fine-mist fire-fighting equipment
Aircraft engine cooling systems
The final rinse of car and window washing systems as it leaves no smears

Packing Size:

25.00 Ltr.

Image:

Thumb:

Short Description:

Extremely high quality. It is produced by means specialist piece of equipment to produce it called a demineralisation plant or a deionisation plant. After completion of chemical treatment .

DM water

It is a well - balanced blend for boiler water treatment products, resulting in a scale and corrosion control by one shot operation. A one-step treatment to control the formation of rust and scale in low pressure and auxillary boilers with working pressure up to 20 bars.

Alias:

Liquitreat, Nalfleet® BWT LIQUID PLUS, Care Treat 3 Boiler 2, Drew Ameroid, Arboiler WT, BWT 104P ( Nor chem ), B.W.T. NEW FORMULA (EQUAL TO DREW - AGK 100), DM-511, EAZY BWT-1, ONE SHOT BWT

Active Matter:

54-60

Application:

The dosage rate is dependent on bioler operating condition, feed 2-3 ltrs of RXSOL-50-5001-025 solution for per thousand ltr of bioler water then control the system by periodic Alkalinity test procedure. If p-Alkalinity is below 200 ppm increase the ratio of RXSOL BWT 5001 solution. If p-Alkalinity is above 400 ppm reduce the concentration of RXSOL-50-5001-025 solution by dilution with water. RXSOL-50-5001-025 is strongly alkaline.RXSOL-50-5001-025 is best applied heat or diluted with any convenient strength on a continuous basis using a suitable chemicals pump. The product should be applied to the boiler feed tank or feed line to ensure adequate mixing.

CHARACTERISTIC :

Convenient liquid treatment, which provides the basic alkalinity on which successful water treatment depends.
Provides optimum conditions for hardness control to function.
Neutralizes acid conditions.
Will assist in keeping silica in suspension.
Simple test to determine level of treatment.
Can be used in boilers of all pressures.
Can be used as a neutralizer after acid cleaning operations
Suitable for use with all auxiliary boilers; waste heat units; economizers, package boilers, smoke and water tube boilers.
Dispersant action suspends sludge and sediment particles for efficient blow down.
Oxygen scavenging for optimum protection.
Protects boiler, steam lines, condensate lines and feed water lines from corrosion.
Fast action due to catalyst.
Simple test to determine level of treatment.

Packing Size:

25.00 Ltr.

Image:

Thumb:

Using Procedure:

Control is by simple boiler water tests or RX CLEANSERS can provide a suitable test kits for this purpose.

Used in low pressure and auxillary boilers

:::::::::::::::::::::Alkalinity TEST FOR BOILER & COOLING WATER ::::::::::::::::::::::::

REAGENT & APPARATUS :
Reagent: RXSOL TK 7 , TK 8 , TK 9 , . Apparatus : TEST TUBE , Titrator or DROPPER

PROCEDURE for p-ALKALINITY test ( STEP WISE ):

Measure 10 ml of SAMPLE WATER in graduated TEST TUBE / CYLINDER
Add 1-2 drops of RXSOL TK7 and mix with the stirring rod , If sample turns red / PINK ( which indicates presence of p-Alkalinity ) then follows 3^rd step otherwise if sample remains colourless ( Record p-Alkalinity = 0 ) .
Add RXSOL TK9 drop by drop ( by counting ) , mixing with the stirring rod until colour just disappears. Each drop is equivalent to 25 ppm of p-Alkalinity , expressed as CaCO₃

RESULT : Each DROPS is equivalent to 25 PPM of Alkalinity .

NOTE : p-Alkalinity VALUE = 25 X ( Total Number of DROPS of TK9 , during 3^rdstep )

PROCEDURE for p-ALKALINITY & TOTAL ALKALINITY ( STEP WISE ):

Measure 10 ml of SAMPLE WATER in graduated TEST TUBE / CYLINDER
Add 1-2 drops of RXSOL TK7 and mix with the stirring rod , If sample turns red / PINK ( which indicates presence of p-Alkalinity ) then follows 3^rd step otherwise if sample remains colourless ( Record p-Alkalinity = 0 ) then proceed to STEP- 4.
Add RXSOL TK9 drop by drop ( by counting ) , mixing with the stirring rod until colour just disappears. Each drop is equivalent to 15 ppm of p-Alkalinity , expressed as CaCO₃
Add 2-3 drops of RXSOL TK8 and mix with stirring rod , the sample will turn to BLUISH-GREEN .
AddRXSOL TK9 carefully by counting drop by drop and mixing throughly until a light reddish pink colour develop.

RESULT : Each DROPS is equivalent to 25 PPM of Alkalinity .

NOTE : p-Alkalinity ppm CaCO₃VALUE ( A ) = 25 X ( Total Number of DROPS of TK9 , during 3^rdstep )

Total Alkalinity ppm CaCO₃VALUE = A + { 25 X ( Total Number of DROPS of TK9 , during 5^th step )}

NUMBER OF DROPS OF TK9 p-Alkalinity as CaCO₃

1 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>25
2 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>50

3 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> 75
4 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> 100

5 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> 125
10 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> 250

20 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> 500
30>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>750

40 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> 1000

Optimum Result : p-Alkalinity level is between 100 to 150 PPM is suggested.

if p-Alkalinity level is more then 150 ppm then level should be reduced by increased BLOW DOWN process with immediate effect.

For Below 50 ppm , Dose ½ Ltrs of RXSOL-50-5001-025 for 1000 Ltrs of BOILER WATER , to maintain p-Alkalinity level 100 ppm.

Refill pack : REPLACEMENTS

TK7 : ECONOMIC PACK ( 100 / 200 / 500 ml ) available

TK8 : ECONOMIC PACK ( 100 / 200 / 500 ml ) available

TK9 : ECONOMIC PACK ( 100 / 200 / 500 ml ) available

Note:

Basic Boiler System Schematic

Below is a summary of problems associated with the common impurities in water and solutions to each problem.

List Of Problems Caused By Impurities In Water

Impurity (Chemical Formula)	Problems	Common Chemical Treatment Methods
Alkalinity (HCO₃-, CO₃^2-and CaCO₃)	Carryover of feedwater into steam, produce CO₂in steam leading to formation of carbonic acid (acid attack)	Neutralizing amines, filming amines, combination of both, and lime-soda.
Hardness (calcium and magnesium salts, CaCO₃)	Primary source of scale in heat exchange equipment	Lime softening, phosphate, chelates and polymers
Iron (Fe³⁺and Fe²⁺)	Causes boiler and water line deposits	Phosphate, chelates and polymers
Oxygen (O₂)	Corrosion of water lines, boiler, return lines, heat exchanger equipments, etc. (oxygen attack)	Oxygen scavengers, filming amines and deaeration
pH	Corrosion occurs when pH drops below 8.5	pH can be lowered by addition of acids and increased by addition of alkalies
Hydrogen Sulfide (H₂S)	Corrosion	Chlorination
Silica (SiO₂)	Scale in boilers and cooling water systems	Lime softening

Featured Product :

Featured Product

Article News:

Boiler Maintenance Chemicals

Sodium Hexametaphosphate to precipitate calcium in low-pressure boilers

Chelant Treatment for Boiler

Boiler Treatment tips

Marine Chemicals supplier

Why Marine Chemicals?

Short Description:

Chemical feed should be continuous. Chemical pumping rates can create problems especially for neat feed set ups. Using on/off feed systems such as a recycle timer can create problems. Chemical feed pumps should be sized or product strengths should be adjusted to allow continuous feed.

Steam and carbon dioxide leave continuously, so setting up a neutralizing amine pump to feed intermittently can lead to wide variations in condensate pH control. If sampling is done from a condensate receiver, the tank volume may buffer the variations and the changes may not be noticed, but corrosion could be occurring to areas of the piping that see the rapidly changing pH.

If polymeric dispersants, phosphonates, phosphate, or chelants are fed intermittently into the feedwater using a recycle timer, and the amines are not fed continuously, a cycle of iron slugs returning in the condensate can be followed by slugs of high dispersancy cleaning of the iron from the deaerator and dragging it into the boiler.

Load changes can affect chemical concentrations when the chemical feed is base fed. Example: Steam production of one million lbs./day; 4% blowdown; 20% active boiler polymer product fed at 5 pounds per day. The calculated daily average polymer concentration would be 24 ppm. Assume peak plant production load is 60,000 lbs./hr., but during the overnight hours the load is only 5,000 lbs./hr. If the dispersant is being fed continuously over the 24 hours, during the 8- hour low load period, the boiler polymer concentration would have increased to over 200 ppm. Upon high fire when production resumes, carryover is very possible because of over concentrating the polymeric dispersant.

Chemical feed needs to be paced to steam production, especially where significant load changes occur.

Carbon dioxide can concentrate in steam and condensate making neutralizing amine treatment impractical. Carbon dioxide levels can be relatively low in steam exiting a boiler at only a few ppm, but if there are areas where it becomes “trapped” and can accumulate, concentrations can reach extremely high levels into the hundreds or even thousands of ppm.

CO2 is a non-condensable gas. It has a distribution ratio in the steam piping and condenses at points throughout the system. At the boiling point, the solubility of the gas in water is extremely low. The solubility of the CO2 is actually lower in the condensate than it is in the steam. For the CO2 to escape from the steam into the water it will accumulate in the steam space just above the water level until the partial pressure becomes high enough for the CO2 in the incoming steam to be able to exit into the condensate. This creates a steady state condition of CO2 coming in and exiting, but an area of severe localized corrosion occurs where the carbon dioxide concentration is high.

The highest CO2 concentration normally occurs just above the condensate water level. If there is an area where condensation is occurring and running down pipes or the sides of vessels, the CO2 concentration will be very high and the pH will be about 5.3 – 5.5 in that location creating high corrosion rates.

The solubility of CO2 increases dramatically as the condensate temperature falls below 212 °F. When there is an accumulation of CO2 in an area and the condensate temperature is relatively low, the amount of carbon dioxide going into solution will be extremely high. Where low-pressure steam is used that contains CO2 and the heat exchange process has relatively close temperature differentials between the steam and the condensate, there is potential for high uptake of the CO2 into the condensate and localized low pH.

Neutralizing amines are selected in an effort to condense in the right concentrations to carbon dioxide condensation levels throughout the steam system. Neutralizing amines cannot control corrosion where this localized accumulation of carbon dioxide occurs since the high CO2 overwhelms the demand for the amine. Even point source addition of amine may not be able to satisfy the demand.

Where the concentrating effect of CO2 occurs, methods of reducing the problem include eliminating or minimizing CO2 in the steam, venting off the CO2 in the localized area, eliminating condensate in the area, applying a filming amine or metal passivator, or using higher temperature steam and increasing condensate temperature to reduce the CO2 content in the condensate.

BWT ONE SHOT

Hardness Control is a Liquid product used for the reduction of hardness in boilers and to adjust hardness and phosphate. Hardness Control is highly soluble in water and It will precipitate calcium hardness as a non-adherent sludge.

Alias:

Green HC, Phosphate Control, Chem 3221, Sodium Hexa Meta Phosphate, ST-DOS H-200

Application:

Hardness Control is formulated to form a precipitate with calcium ions which will not adhere to metal surfaces but are in a form suitable for blowdown.

Packing Size:

25.00 Ltr.

Image:

Thumb:

Using Procedure:

For optimum results dose Hardness Control direct to the boiler via the bypass pot-feeder. The dry powder should be dissolved in hot water (50°C) at a ratio of 1 part powder to twenty parts condensate (e.g. 500 grams/10 litres). Ensure that treatment is fully dissolved before dosing.

Dosage and control

	Phophate test result in pPM PO4
Pressure	0 - 10	10 - 20	20 - 30	30 - 40	40 - 50	> 50	Control range
0-40 Bar 0-588 PSI	23	11.5	Satisfactory	Satisfactory		Blow Down	20-50
41-60 Bar 589-880 PSI	17	5.5	Satisfactory	Blow Down		Blow Down	15-30
> 60 Bar > 880 PSI	5.5	Satisfactory	Satisfactory	Blow Down		Blow Down	10-25

Select row on righthand side for applicable pressure range. Compare test result with comment in table and dose stated amount of product per ton boiler water volume.

These are recommended values based on experience and are in no way intended to replace the boiler manufacturer's specifications or company regulations.

Note:

Benefit and Features

Highly active phosphate based compound, economical in use.
Easily dissolved in water for dosing.
Scale problems due to calcium are eliminated.
Maintains sludge in a non-adherent state for ease of blow down.
Simple test to determine level of treatment.
Can be used for boilers of all pressures.
Rxsol Hardness Control does not influence the alkalinity in the system

Featured Product :

Featured Product

Article News:

Hardness Control Liquid a perfect solution for water treatment from Rx Marine

Short Description:

Liquid product used for the reduction of hardness in boilers. Hardness Control is highly soluble in water and It will precipitate calcium hardness as a non-adherent sludge.

Phosphate bsed Corrosion inhibitor and hardness conditioner

FAQ:

Corrosion protection boiler chemicals

Aquatuff high foam liquid always be wise decision to clean ship cargo hold. As before loading of cargo surveyor first demand is - Holds must be thoroughly cleaned and dry and trace free of previous cargo in frames.

Alias:

High Foam detergent for ship cargo hold cleaning

Active Matter:

45-50

Application:

Most Helpfull cleaner for preparation of a cargo hold. In general cleaning of vessel's cargo holds Aquatuff High Foam plays very important role in washing down with use of chemicals. Aquatuff High foam classified as Marine Chemicals, Cleaning Chemicals; Cargo Hold Cleaning detergent.

Packing Size:

210.00 Ltr.

Image:

Thumb:

Using Procedure:

Refer this link for complete set of HOLD CLEANING KIT ::: http://rxmarine.com/Ship-hold-cleaning-kit-set-supplier

The Importance High-Pressure Cleaning

The job of high-pressure cleaning can be done easier & quicker by simply using AquaTuff incorrect dosages. Using a high-pressure cleaner alone, without any CLEANER, will not achieve optimal cleaning results High-pressure cleaning primarily refers to cleaning of Hard surfaces, such as Decks, Tanks, Engine-rooms, etc. and in the majority of cases the cleaning is done according to the so-called two-step method:

Step 1: Spraying the AquaTuff over the area to be cleaned.
Step 2: Washing down the area using a high-pressure water jet.

After the AquTuff has been sprayed on the surface and before the wash down begins, the chemicals penetrate & thoroughly moistens dirt & other grime. During wash down, the AquaTuff thoroughly dissolves the particles of dirt, even oil and fat, in the water spray and thus achieves optimal cleaning results.In addition to being more effective, the use of AquaTuff substantially reduces the time required for the Cleaning operation, as well as preventing dirt from reforming on the surface. The use of AquaTuff in correct dosages is half the job done.

General Cleaning :- AquaTuff can be used for all types of cleaning & degreasing & may be applied by Brush, Hand spray, high and low-pressure washing machines etc. Time necessary for cleaning depends on the nature and thickness of the deposits. 20-30 min. will suffice for most applications. Hardened, carbonised or aged deposits may require up to 4 hours. If the cleaning solution is not heavily contaminated, it may be re-used at a later stage. If allowed to cool, the de-gassing procedure must be repeated. Depending on the degree of contamination AquaTuff should be mixed with warm water at a rate of 50-200 ml per 10 litres. i.e. 1 cup of AquaTuff to a bucket of water. The aqutuff solution can be applied simply by mops, brushes or rags, or by dipping the soiled articles into the Aquatuff solution. After cleaning, rinse off with cold or warm water. Due to high foaming properties, AquaTuff is not recommended for washing machines.

20-50 % with fresh water . Also acts as an acid-neutralizing agent for Boiler & Colling systems during cleaning & maintenance.
Heavy Soil deposition Use Undiluted from to 20-50% diluted with water.
Medium soil deposition 10-20% diluted with water.
Light Soil ( general degreasing ) 5-10% diluted with water.

Note:

Aquatuff high foam is absolutely free along with the purchase of slip coat - Hold block materials. Aquatuff High foam Free 1000 Ltr against 1000 Ltrs purchase of Slip Coat Plus at our Mumbai, Visakhapatnam, Ennore, Kolkata, Kandla - Gandhidham, Fujairah - Gulf.

For degreasing and removal of residues of minerals oil , coal stain and soot from surface.
superior & powerful alkaline cleaner. It is low toxic product with an exceptional solvency power on soil & oily matter & having good foaming qualities. It is free from Hydrocarbon solvents , Biodegradable and minimizes the extreme hazards to personnel in handling materials .
Safety Phrases
S-2 Keep out of the reach of children.
S-26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
S-36/37/39 Wear suitable protective clothing, gloves and eye/face protection.
S-45 In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible).

Preparation

Preparing Cargo Holds for loading Grain depends on the previous cargo.

1. Cargo Holds must be thoroughly cleaned and dry and trace of previous cargo in frames, beams, girders, and other structure.

2. There should not be any loose rust and or paint scale anywhere in the Cargo Holds, Bulkheads, upper and lower hopper spaces, underneath of Hatch Covers and tank top.

3. There should not be traces of live & dead insect & weevils.

4. Bilge covers should be cleaned of any cargo residues and have enough drain holes. Bilge cover needs to be grain tight but not watertight.

5. Bilge well should be cleaned of previous cargo dray and odour free.

6. Bilge suction should be operational at all the times.

Removal of cargo residue:

Air Blow from top using high pressure air to reach all accessible corners. Cargo to be swept, scrapped & collected in a drum. Attention to be given

• Australian ladder and its platforms and stanchions

• Beams and girders under cross decks

• Frames, beams, girders, and other structure

• Large pipes holding brackets behind the pipes

Then Cleaning and sweeping coal cargo from the hold as maximum possible by HELPER / Crew member

Loose Rust & Paint Scale:

A sharp hand scraper shall be used to take off the peeling rust & paint scale Special attention to following areas:

• Australian ladder and its platforms, hand rails and stanchions

• Australian ladder and its platforms and stanchions

• Beams and girders under cross decks

• Frames, beams, girders, and other structure

• Large pipes holding brackets behind the pipes

• Hatch coamings and under hatch covers

• Booby hatches & cover

Tank top loose rust

Tank top should be free of loose rust and cargo residue

Any rust which can be scraped by hand scrapers should be removed.

The tank top should be rinsed with fresh water

Cleanliness of cargo hold bilges

Hold bilges must be cleaned thoroughly to remove all residue, rust particles and cargo stains etc.

The filter (Rose Box) must be cleaned thoroughly

The bilge well sections shall be washed with continuous running of sea water to remove all odour and later rinsed with fresh water

Related Products:

AQUATUFF LIQUID 50 Ltr

Cement Remover RX Hold

COAL REMOVER rx hold 50 Ltr

Lime Remover HD 25 Ltrs

Slip Coat RXSOL HOLD BLOCK 210 Ltr

Hold Wash Concentrate RX

Safety Accessories:

Hand Gloves Chemical resistance

Goggle Chemical Protective

Burlup - Burlap

Featured Product :

Featured Product

Article News:

Aquatuff marine hold cleaning and degreasing chemicals

Aquatuff MSDS

Aquatuff High Foam ship hold cleaning detergent

Differences between Aquatuff High Foam and Aqautuff

Aquatuff high foam application and cleaning method and manual

Aquatuff Cleaning action

Aquatuff High Foam Ship Hold cleaning detergent

How to clean Carbon deposits from Ship hold Bulk carrier?

Aquatuff High Dense Foam to clean ship hold vertical surface

Aquatuff High Foam General description

Short Description:

Very effective alkaline ship hold cleaner also can be use as multi purpose ship hold cleaning and general digressing agent. its heavy molecular surfactants rapidly reacts with water and produce effective cleaning solution .May be applied by brush, hand spray and by high and low pressure washi

Information:

Aquatuff High foam is specialized ship hold bulk carrier cleaning chemicals. Our group team also providing direct online support for cleaning tips during Hold cleaning of ships. Aquatuff High Foam MSDS and Using procedure also available online to our customer. We are one of largest ship hold cleaning chemicals supplier in India - Middle East which also covers Lime Remover, Coal Remover, Slip coat, Hold Wash and many more...Pl. click here ( http://www.rxmarine.com/HoldSolution-22 ) to know our various range of Hold Cleaning products...

Aquatuff for bulk carrier cargo hold cleaning alkaline detergent, Other then aquatuff cargo hold cleaning chemicals lime washing chemicals for cargo holds and pet coke cargo hold washing detergent also popular for specificed lime and and pet cargo. We are also keeping ready stock of cement hold cleaning chemicals, Hold Block - Slip Coat, Hold Wash etc...

Cargo Hold Cleaner, Bulk Hold cleaning etergent, Chemical Agent for hold cleaning, Hold Cleaning Kits detergent

Importance of Alkleen Safety Liquid / Aquatuff Cargo hold cleaner for coal and pet coke:

Aquatuff High foam and Aqua tuff / Alkleen Safety Liquid cleaner is most common marine cleaning chemicals for cargo hold cleaning after coal and pet coke.

Two Major Benefit of cleaning of Pet Coke:-

Pet coke residue contains oil content, which is creating more difficulties during the cleaning operation. Aquatuff high foam and one of our specialized product called Alkleen Safety Liquid which is absolutely non-hazardous and biodegradable cleaner.

Petcokes also have sulphur content which is the main cause of corrosion due to its electrochemical corrosion mechanism. In presence of moisture and sulfur metal surface charges as anodic and damaging the hold paint due to electrical ion charges. Here presence of Alkleen Safety Liquid / Aquatuff increasing the alkaline effect and neutralizes the effect of Sulphur.

Ship marine hold cleaning chemicals

Aqua tuff most suitable for cargo hold and tank cleaning.

Aquatuff High foam plays very important role during ship hold cleaning http://rxmarine.com/Aqua-Tuff-High-Foam-conc , Its high foam abilityincreasing Aquatuff cleaning power on the vertical surface, As liquid product can't sustain on the vertical surface while HIGH composite FOAM can sustain on the surface which is resulting from good cleaning effect.
Extra foaming is major features which is differentiating Aquatuff high foam to general Aquatuff.

Aquatuff High foam using procedure and cleaning method :
1st Step Cleaning of extra and excess loose particle:::
Before applying Aquatuff high foam on hold surface, Makes sure extra loose cargo particle should be removed manually or Air blown method. Then cleaning procedure can be followed either by high foam machine or Manual.
2nd step is for Mixing and dilution of Aquatuff:::
If cleaning step is with HP machine ( High Pressure ), Then mix concentrated Aquatuff high foam with fresh water, it can be diluted 1 Ltrs Aquatuff High foam with 4 to 5 Ltrs Fresh water.

If cleaning step followed by hand spray, Then apply aquatuff high foam neat on the surface. Approx 1 ltr covers 10 to 12 square meter.

3rd Step final procedure:::

Leave for about 30 – 45 minutes. The surface remains wet. Wash down with hot water at around 80 - 90 degree. Rinsing procedure can be repeated 1 to 3 times if required for Cargo Tank and Cargo Hold Cleaning.

Aquatuff High Foam supplier in Mumbai, Nhava Seva, Pirpav, Surat - Hazira, Kandla - Gandhidham, Sikka - Mundra, Manglore - Goa, Vizag - Visakhapatnam, Gangavaram, Kakinada, Chennai - Ennore, Kolkata, Haldia, Paradip, Buj buj, Dubai - Sharjah, Fujairah Middle East

Shipping Tanker, Bulk Carrier cleaning agent, Hold Cleaning Agent. Heavy Duty Alkaline Cleaner with Extra Foaming Effect.

Aquatuff high foam is absolutely free along with the purchase of slip coat - Hold block ( Pre load ) materials. Aquatuff High foam Free 1000 Ltr with the purchase of 1000 ltrs Slip Coat Plus is available at Mumbai, Visakhapatnam, Ennore, Kolkata, Kandla - Gandhidham, Fujairah - Gulf

Here the question that arises is why Aquatuff Cleaner is so important during Ship Hold Cleaning?

Aquatuff is alkaline in nature which neutralizes the acidic residue created due to the presence of moisture and products like coal, sulphur, salt etc. And emulsification effect of aquatuff makes alll oil stain water soluble. It means Aquatuff's major role is to neutralize the acidic residue and emulsifying Oil residue. One more important feature of Aquatuff high foam results in the formation of dense foam with high-pressure machines, which can easily be applied even on vertical surfaces.

Aquatuff High Foam - Acts as an Acid Neutralizer - Useful for coal, Sulfur, Salt as its residue when in contact with water, is acidic in nature which directly damages the painted and metal surfaces.

Aquatuf High Foam - Acts as an Oil residue Emulsifier - Useful for removal of coal and oily residue.

Aquatuff High Foam - Results in Dense foam - Can be applied on the vertical surface for the long duration.

The largest supplier of Aquatuff high foam in Asia ( India and Middle East). More details of Aquatuff High Foam like MSDS and Using procedure of will be available through this link:

http://rxmarine.com/aquatuff-emulsifier-liquid link http://rxmarine.com/aquatuff-emulsifier-liquid

Aqutuff high foam cleaner detergent for ship hold cleaning

FAQ:

What is Aquatuff High Foam used for?

Cargo hold cleaner for coal and pet coke

Importance of Aquatuff ?

Metal Brite for Ship Hold rust cleaning?

Aquatuff is Free

RXSOL RO-3 is a Metal Oxide Cleaner for Foulant which is caused by heavily deposit metal oxide CaCO3, CaSO4, BaSO4,for RO Membranes. This Membarance cleaner is also very effective fo removal of Acid insoluble Deposits like calcium sulfate Phosphate .

Alias:

NASCO RO-3, PERMACLEAN 33, Metal Oxide Cleaner, MC-3 CHEMICAL POWDER FOR RO PLANT

Packing Size:

25.00 Kg.(PWD)

Image:

Thumb:

Related Products:

RXSOL RO - 2 Bio Film Cleaner

RXSOL RO - 3

RXSOL RO - 4 Organic Cleaner

RXSOL RO - 5

RXSOL RO - 820

RXSOL RO - 901 Passivation

RXSOL RO - 902

RXSOL RO - 903

RXSOL RO - 905

RXSOL RO -1 Heavy Soil Cleaner

Safety Accessories:

Goggle Chemical Protective

Gloves Disposable

Featured Product :

Featured Product

Short Description:

CHEMICAL CLEANING POWDER FOR RO PLANT

Bentonite Supplier for Oil Field Industries. It is a drilling - grade Bentonite which is naturally occuring clay .It is a High Yield Natural Sodium montomorillonite. It meets API 13A Standards.

Bentonite, very fine grind material mostly composite by clay mineral, especially montmorrilonite which chemically describe as hydrous alumina-silicate which contain small amounts of alkali and alkali -earth metals.

Alias:

Bentonite API, Montmorrilonite

Application:

• It is Viscosifier and Filtration control agent for water based Mud Systems.
• It is used in drilling muds for controlling bore hole stability. It is utilized in drilling muds to extract drill cuttings from the bit.
• It is also used for clearing cat litter

Bentonite, sometimes refer as sometimes referred to as Montmorrilonite is a naturally occurring substance, composed of a number of layers, each approximately 10 angstroms thick, and each consisting of two tetrahedral and one octahedral unit. This structure is responsible for three important characteristics, the ability to absorb large amounts of moisture, the ability to exchange ions and thixotropic gel formation.

Bentonite Powder

We are reputed as one of the most overruling Bentonite Mineral Powder Manufacturers and Suppliers in India. The unmatched quality and efficacy of Bentonite Powder in various sectors like Drilling, Effluent Treatment, Electrical, Engineering, Fertilizer, Foundry, Iron ore Pelletization, Liquor & Food, Pesticides and Pharmaceutical has played a vital role in the enhancement of the demand. Moreover, Bentonite Clay Powder is available in varied grades.

Application

Drilling

Effluent Treatment

Electrical

Engineering

Fertilizer

Foundry

Iron ore Pelletization

Liquor & Food

Pesticides

Pharmaceutical

Packing Size:

50.00 Kg.(PWD)

Image:

Thumb:

Using Procedure:

Bentonite can be Broadely classified in 2 grades :

Granular: Granular is the preferred option for filling trenches where the conductor is covered with Bentonite and then water poured over and mixed in the trench.

Powder: Powder is the preferred method for pouring into bore holes to en-sure the mixture is of a thin enough consistency to reach the bottom of the bore hole. If diamond drilling is required for deep holes, possible 40m depths and deeper and the Bentonite is to be pumped through the core in to the hole, then powder would be the preferred option.

The greatest application of bentonite in industries is the result of its swelling property, while combine with water able to perform multitude jobs. The sodium bentonite having more water absorption capacity makes it suitable for industries like Foundry and Civil engineering application and the calcium bentonite absorb lesser than Sodium still it has some special application like cosmetics, paper, Animal feed binder as many more to describe. Swell Well Mine Chem drilling grade Bentonite is basically a sodium bentonite acquired naturally from the mines. The mineral is processed using the advanced chemical technology for drilling from ores. The below features highlights the quality of the Swell Well Mine Chem Drilling Bentonite, Offers impermeability, Provides high barrel yield. Bentonite is valued in foundry sand binding, drilling mud and sealing agent in civil engineering works, bentonite is used as a mud constituent for oil and water well drilling. Swell Chem Mine is offering Bentonite products for drilling industry. What is Drining Bentonite ? Drilling Bentonite is the Bentonite formed to be used in drilling mud or fluid.

Note:

Advantage

• It helps improve hole cleaning capacities of drilling fluids.
• It is effective as a filtering agent.
• It promotes borehole stability.
• It can be added directly to fresh water or fresh water based drilling fluids.

Related Products:

Dolomite

Calcium Chloride Anhydrous

SODIUM Chloride Crystal PURE

Safety Accessories:

Hand Gloves Chemical resistance

Chemical Handling Apron

Featured Product :

Featured Product

Article News:

Water Treatment Chemical STOCKIST in India - Middle East

Short Description:

Maximum swelling property, while combine with water, Our fine quality of sodium bentonite having more water absorption capacity then ordinary one.

Information:

Bentonite premium quality products exporter from India to Middle East - Dubai.

Various grade of Bentonite :::

Drilling Grade 1

API 13A Section – 9 Grade Bentonite Powder:

Physical Analysis:

PROPERTIES	PROTOCOL	UNIT	REQUIRED	RESULT
Viscometer Dial Reading at 600 rpm	API Spec. 13A:2004/ ISO 13500: 1998	r/min	30	36
Yield Point / Plastic Viscosity Ratio	API Spec. 13A:2004/ ISO 13500: 1998	_	3 Max	2.5
Filterate Volume	API Spec. 13A:2004/ ISO 13500: 1998	ML	15 Max	14.6
Moisture Content	API Spec. 13A:2004/ ISO 13500: 1998	% by weight	10.0 max.	10
Dry Screen Analysis(Residue Greater than 75 Microns)%	API Spec. 13A:2004/ ISO 13500: 1998	% by weight	4.0 max.	3.0 - 4.0

Drilling Grade API Packing 25 Kgs

IOP Grade Bentonite lumps :

Properties	Protocol	Unit	REQUIRED
Moisture Content	API Spec. 13A:2004/ ISO 13500: 1998	% by wt.	12% to 40 % max.
LOI	IS:2000(P-1)-1985	% by wt.	5 – 10.
Free Swelling Volume 2gm/100ml	ASTM D 5890:1995	ml	32 min.
PH Value of 5% gel	IS:6186-1986	pH	8.0 – 10.0
Plate Water Absorption (16 hours)	ASTM E 946	%	720- 760
Gel Time 2.5gm/25 ml	IS:12446-1988	second	Instant
Methylene Blue Value	API spe 131:2004/ ISO 10416:2002	mg/gm of clay	350 - 400
Lumps size	IS:6186-1986	%	10 to 40 m.m.

Chemical specification:

Alumina as AL2O3%>15.0-19.0 Sodium max 2.70

Calcium as Cao%1.5-2.0 Na2O 2.0-2.5

Mgo 2.5-3.5 iron as Fe2o3% 13.0-18.0

IOP Grade Lumps | 25 Kg Packing

Product: Benotonite Powder for Grouting

Physical Analysis:

Properties	Protocol	Unit	Result
Liquid Limit	IS:12446-2007	ml/100 gm	350 - 450
Moisture Content	API Spec. 13A:2004/ ISO 13500: 1998	% by wt.	12.0 Max
Dry Screen Analysis (passing through 75 um sieve)	IS:12446-2007	% by. Wt.	85.0 min.
Free Swelling Volume 2gm/100ml	ASTM D 5890:1995 or IS:12446-2007	ml	30 min
PH Value of 5% gel	IS:12446-2007	pH	9.5 - 10.0
Gel Time 2.5gm/25 ml	IS:12446-1988	second	Instant
Filterate Volume	API Spec. 13A:2004/ ISO 13500: 1998	ml	20 max
Viscosty at 600 rpm	API Spec. 13A:2004/ ISO 13500: 1998		30 min
Methylene Blue Value	API spe 131:2004/ ISO 10416:2002 / IS:12446-2007	mg/gm of clay	350 - 400

Grouting Grade | 25 Kg Packing

PRODUCT: Ceramic Grade Bentonite Powder

Physical Analysis:

Properties	Protocol	Unit	Result
Free Swelling Volume 2 gm/100ml	IS:12446-2007	ml	12 - 18
Base Exchange Capacity	IS:12446-2007		70 - 80
Moisture Content % by weight	IS:12446-2007	%	10.0 - 12.0
PH Value 2% slurry	IS:12446-2007	0pH	8 - 9
Quartz Content	IS:12446-2007	%	2 - 3 %
Dry Mesh % Passing 200 B.S.S	IS:12446-2007	%	85 Minimum

Ceramic Grade | 25 Kg Packing

Sodium montomorillonite

SPECIFICATION

Application:

USES:
• Flocculation in municipal water supply, sewage and industrial effluent.
• Paper manufacture.

Packing Size:

25.00 Ltr.

Image:

Thumb:

Note:

AVAILABLE IN:
• Bulk tankers
• 1000 litre IBC
• 200 litre Mauser

Featured Product :

Featured Product

Short Description:

Flocculation in municipal water supply, sewage and industrial effluent and for Paper manufacture.

Polyaluminium Chloride Powder supreme grade Polyaluminium Chloride Powder. We formulate these chemicals using quality compounds to obtain pure chemicals. The powder is widely used in water treatment plants for purification of water. Its also used in deodorants and antiperspirants. Our experienced quality examiners test the Polyaluminium Chloride Powder on the basis of various parameters before forwarding it for delivery. Furthermore, we are able to deliver these chemicals within the time-specified by our clients.

Alias:

PAC

Application:

Polyaluminium Chloride Applications
A part from the use in water treatment and urban water supply, Polyaluminium Chloride also finds application in drilling exploration, cosmetic, chemical, paper and various other industries.

Advantages of Polyaluminium Chloride:
• A wide range of pH value from 5 to 9 can be adapted by Polyaluminium Chloride and can be easily reduced to basicity, after processing
• It can easily adapt the different temperature of water during summer and winter and at different regions, i.e, the south and the north of China.
• It is best suited for an automatic dosing device of alum (hydrated double sulphate of potassium and aluminium)
• Its purifying effect is much better than other organic flocculants. It easily purifies the water on low-temperature and low turbidity. Also, it lower the water treatment cost by 20-80%.
• The dosage of Polyaluminium Chloride is smaller than other flocculants, which efficiently improves the quality of treated water.
• With huge size and rapid condensation service life of cellular filter (sedimentation basin), the quick formation of FOLC at low temperature is easily possible using the chloride.

Packing Size:

25.00 Kg.(PWD)

Image:

Thumb:

Using Procedure:

Polyaluminium Chloride Usage
• The user can allocate the remedy concentration of the product by test and can easily determine the appropriate dosage, which is to be added after they are dissolved and diluted.
• The perfect dilution ratio of liquid product is 5 to 50% and the solid product is 2 to 20%.
• The solid product dosages is 1-15kg/1000 tons water and liquid product dosage is 3-40kg/1000 tons water
• The perfect amount of dosage can be determined after coagulation tests and experiments.

Items	Data
Appearance	Solid powder, yellow
Al2O3 %	29 min
Basicity %	.0~90.0
Insolubles %	1.5 max
pH(1% water solution	.5~5.0

Note:

Salient Features of Polyaluminium Chloride:
• Made from pure raw material
• Used for drinking water treatment and paper mills as retention agent
• Appearance: solid powder, white
• Al2O3: 29% (min.)
• Basicity: 50.0% ~ 85.0%
• Insolubles: 0.5% (max.)
• PH (1% water solution): 3.5 ~ 5.0
• SO42-: 3.5% (max.)
• N: 0.09% (max.)
• As: 0.0005% max
• Mn: 0.045% (max.)
• Cr6+: 0.0015% (max.)
• Hg: 0.00002% (max.)
• Pb: 0.003% (max.)
• Cd: 0.0006% (max.)
• Fe: 0.008% (max.)

Featured Product :

Featured Product

Short Description:

A part from the use in water treatment and urban water supply, Polyaluminium Chloride also finds application in drilling exploration, cosmetic, chemical, paper and various other industries

Hydrogen peroxide (H2O2) is the only germicidal agent composed only of water and oxygen. Like ozone, it kills disease organisms by oxidation! For this reason, Hydrogen peroxide is considered the world’s safest all natural effective sanitizer.

Alias:

Hydrogen Peroxide, Mild Disinfectant and cleaning agent

Active Matter:

Application:

Application : Adults the elderly and children : Apply the solution directly with a PAD of cotton wool required.

Packing Size:

500.00 Bottle Liq

Image:

Thumb:

Using Procedure:

Active Ingredient : Hydrogen Peroxide 6%

Note:

1. Cuts and infections

Soak any infections or cuts in 3% for five to ten minutes several times a day. Even gangrene that would not heal with any medicine has been healed by soaking in Hydrogen peroxide. Put half a bottle of hydrogen peroxide in your bath to help rid boils, fungus or other skin infections.

2. Rejuvenating Detoxifying Bath

Use about 2 quarts 3% Hydrogen peroxide to a tub of warm water. Soak at least 1/2 hour, adding hot water as needed to maintain a comfortable water temperature.

3. Foot Fungus

To cure a foot fungus, simply spray a 50/50 mixture of Hydrogen peroxide and water on them (especially the toes) every night and let dry.

4. Bird Mites Infections

Patients infected by tiny mites report that hydrogen peroxide effectively kills the mites on their skins. They spray it on their skin a couple of times (with a few minutes in between the applications) with amazing results.

5. Sinus Infections

A tablespoon of 3% Hydrogen peroxide added to 1 cup of non-chlorinated water can be used as a nasal spray. Depending on the degree of sinus involvement, one will have to adjust the amount of peroxide used.

6. Wound Care

3% H2O2 is used medically for cleaning wounds, removing dead tissue, and as an oral debriding agent. Peroxide stops slow (small vessel) wound bleeding/oozing, as well.

Some sources recommend soaking wounds for five to ten minutes several times a day. However, washing and rinsing action is sufficient. You shouldn’t leave the solution on open tissue for extended periods of time as, like many oxidative antiseptics, Hydrogen peroxide causes mild damage to tissue in open wounds. Therefore it is important to use with caution.

Personal Care

7. Mouthwash

Many people don’t realize that hydrogen peroxide makes a very effective and inexpensive mouthwash. Take one capful (the little white cap that comes with the bottle) and hold in your mouth for 10 minutes daily, then spit it out. You will not have canker sores and your teeth will be whiter. Use 3% H2O2 – add a dash of liquid chlorophyll for flavoring if desired.

8. Toothpaste

Use baking soda and add enough 3% H202 to make a paste.

9. Toothbrush

Or, just dip your brush in 3% H202 and brush. Soak your toothbrush in Hydrogen peroxide to keep them free of germs.

10. Tooth Ache

Hydrogen peroxide is not a pain killer; however, as an anti-viral, antibacterial and anti-fungal agent, it is effective at treating the pathogen that is causing the infection. The following is from my own personal experience: My dentist wanted to give me a root canal some time ago as one tooth was inflamed and, in her opinion, would die. I felt some discomfort but told her that I would give it chance to heal. I rinsed with hydrogen peroxide (several times a day) as well ascoconut oil (once a day). The discomfort went away and I have had no further problems with the tooth.

If you have a terrible toothache and cannot get to a dentist right away, put a capful of 3% Hydrogen peroxide into your mouth and hold it for 10 minutes several times a day. The pain will lessen greatly.

11. Tooth Whitening

Having used 3% Hydrogen peroxide as a mouth wash for sometime ago, I am thrilled to note that my teeth have been beautifully and effortlessly whitened. I used to pay so much for professional whitening, those silly strips and uncomfortable trays. Live and learn.

12. Douche

Add 2 capfuls of 3% Hydrogen peroxide in warm distilled water once to twice a week to remove even chronic yeast infections.

13. Colonic or Enema

For a colonic, add 1 cup (8 ozs.) 3% H202 to 5 gallons warm water. (Do not exceed this amount) For an enema, add 1 tablespoon of 3% H202 to a quart of warm distilled water.

14. Hair Lightening

Peroxide is a bleaching agent and is used for lightened hair. Dilute 3% Hydrogen peroxide with water (50 / 50) and spray the solution on your wet hair after a shower and comb it through. You will not have the peroxide burnt blonde hair like the hair dye packages, but more natural highlights if your hair is a light brown, faddish, or dirty blonde. It also lightens gradually so it’s not a drastic change.

15. Contact Lenses

Hydrogen peroxide is used as a disinfectant in CIBA Vision’s Clear Care no rub contact lens cleaning solution, due to its ability to break down the proteins that build up on the lense from the eye’s immune response, resulting in increased comfort for those with sensitive eyes.

Sanitizing / Disinfectant / Cleaning

16. In the Dishwasher

To disinfect your dishwasher, add 2 oz. of 3% Hydrogen peroxide to your regular washing formula.

17. Kitchen/Household surfaces

Clean your counters and table tops with hydrogen peroxide to kill germs and leave a fresh smell. Simply put a little on your dishrag when you wipe, or spray it on the counters.

Fill a spray bottle with a 50/50 mixture of 3% Hydrogen peroxide and water and keep it in every bathroom to disinfect without harming your septic system like bleach or most other disinfectants will. After rinsing off your wooden cutting board, pour or spray hydrogen peroxide (and then vinegar) on it to kill salmonella and other bacteria.

Keep a spray bottle of 3% (straight) to disinfect the interior of the refrigerator and kids’ school lunch boxes. You can also use hydrogen peroxide to clean glass and mirrors with no smearing. Use it in the bathroom to sanitize the counters, toilets, floors, etc.

Directions: It is best to use two spray bottles rather than mixing the solutions together. Put straight vinegar in one and straight Hydrogen peroxide in the other spray bottle. When you want to sanitize a surface (cutting board, counters, sink, cages, toys, toilets, floors, etc.) spray one mixture on the surface, then the other. When they mix, for a brief time the chemical action of the two make a very powerful sanitizer. You can rinse off the surface afterwards. This applies for kitchen surfaces as well as vegetable and food decontamination.

18. Humidifiers/Steamers

To clear the air, use 1 pint 3% hydrogen peroxide to 1 gallon of water in a humidifier or steamer.

19. Washing/Laundry

You can also add a cup of hydrogen peroxide instead of bleach to a load of whites in your laundry to whiten them. If there is blood on clothing, pour directly on the soiled spot. Let it sit for a minute, then rub it and rinse with cold water. Repeat if necessary.

Peroxide is a perfect alternate solution to keep those clothes white. Also, when chlorinating clothes, they tend to wear out faster – peroxide won’t do that.

20. Laundry / Stain Removing

3% Hydrogen peroxide is an effective stain remove if it is used fairly soon after a spill – although blood stains as old as 2 days have been successfully lifted with Hydrogen Peroxide. If a little peroxide is poured onto the stain it will bubble up in the area of the blood, due to a reaction with catalase. After a few minutes the excess liquid can be wiped up with a cloth or paper towel and the stain will be gone.

3% H2O2 must be applied to clothing before blood stains can be accidentally “set” with heated water. Cold water and soap are then used to remove the peroxide treated blood.

Please note: Hydrogen peroxide will bleach or discolor many fabrics.

Food Preparation

21. Food preparation/decontamination

Combination of vinegar and hydrogen peroxide make a cheap, effective and non-toxic disinfectant agent and is said to be more effective at killing pathogens than bleach. As it is non-toxic, you can use it to cleanse cooking and food preparation areas (as well as fruits and vegetables – see #24). In tests run at Virginia Polytechnic Institute and State University, pairing Vinegar and Hydrogen Peroxide mists, kills virtually all Salmonella, Shigella, or E. coli bacteria on heavily contaminated food and surfaces.

22. Vegetable Soak

Use as a vegetable wash or soak to kill bacteria and neutralize chemicals. Add 1/4 cup 3% H2O2 to a full sink of cold water. Soak light skinned (light lettuce) 20 minutes, thicker skinned (like cucumbers) 30 minutes. Drain, dry and refrigerate. Prolongs freshness.

If time is a problem, spray vegetables (and fruits) with a solution of 3%. Let stand for a few minutes, rinse and dry.

23. Meat Sanitizing

You can also use it to rinse off your meat before cooking.

24. Leftover tossed salad

To help keep leftover salads, spray with a solution of 1/2 cup water and 1 Tbsp. 5%. Drain, cover and refrigerate.

25. Marinade

Place meat, fish or poultry in a casserole (avoid using aluminium pans). Cover with a dilute solution of equal parts of water and 3% H202. Place loosely covered in refrigerator for 1/2 hour. Rinse and cook.

26. Sprouting Seeds

Add 1 ounce 3% Hydrogen peroxide to 1 pint of water and soak the seeds overnight. Add the same amount of hydrogen peroxide each time you rinse the seeds.

Grades of Hydrogen Peroxide

A) 3.5% Pharmaceutical Grade: This is the grade sold at your local drugstore or supermarket. This product is not recommended for internal use. It contains an assortment of stabilizers which shouldn’t be ingested. Various stabilizers include: acetanilide, phenol, sodium stanate and tertrasodium phosphate.

B) 6% Beautician Grade: This is used in beauty shops to color hair and is not recommended for internal use.

C) 30% Reagent Grade: This is used for various scientific experimentation and also contains stabilizers. It is also not for internal use.

D) 30% to 32% Electronic Grade: This is used to clean electronic parts and not for internal use.

E) 35% Technical Grade: This is a more concentrated product than the Reagent Grade and differs slightly in that phosphorus is added to help neutralize any chlorine from the water used to dilute it.

F) 35% Food Grade: This is used in the production of foods like cheese, eggs, and whey-containing products. It is also sprayed on the foil lining of aseptic packages containing fruit juices and milk products. THIS IS THE ONLY GRADE RECOMMENDED FOR INTERNAL USE.

G) 90%: This is used as an oxygen source for rocket fuel.

Related Products:

Potassium Permagnate 500 Gram

Hydrogen Peroxide with Silver Nitrate Microquell shield

ISO PROPYL ALCOHOL IPA

Featured Product :

Featured Product

Short Description:

Hydrogen peroxide is considered the world’s safest all natural effective sanitizer.

Hydrogen Peroxide 6% Solution supplier in Mumbai, Kandla, Visakhapatnam, Chennai, Kolkata, Fujairah, Dubai, Sharjah, Abu Dhabi.

Mild Disinfectan and cleaning agent

Delta Marine And Offshore Services

Account Id:

ACC78478

Billing Address

Billing City:

Mumbai

Billing State:

Maharashtra

Billing Country:

India

Alias:

Chlorine control, Declor-it, Disodium thiosulfate, S-hydril, Sodium hyposulfite, Sodium oxide sulfide, Antichlor, Sodothiol, Sulfothiorine, Ametox

Active Matter:

48-50

Application:

Dechlorination in municipal, pulp & paper, power, and textile water treatment plants, Oxygen scavenger – oil well drilling process Mining industries Aluminum cation reaction

Industrial production and laboratory synthesis

Principal reactions and applications

Thiosulfate anion characteristically reacts with dilute acids to produce sulfur, sulfur dioxide and water-

1.Na2S2O3 + 2HCl →2NaCl + S + SO2 + H2O

Iodometry

In analytical chemistry, the most important use comes from the fact that the thiosulfate anion reacts stoichiometrically with iodine, reducing it to iodide as it is oxidized to tetrathionate:

Photographic processing

2 S2O32− + AgBr →[Ag(S2O3)2]3−+ Br−

Gold extraction

2 S2O32−(aq) + I2(aq) →S4O62−(aq) + 2 I−(aq)

Packing Size:

25.00 Ltr.

Image:

Thumb:

Using Procedure:

Process for DE CHLORINATION :::

Take 500 ml of Sodium Thiosulfate stock solution.

Add two drops of the stock solution per one gallon of the water to be treated.
One gallon can treat 37,850 gallons or more. Over-dosage is virtually impossible.

Note:

Analytical chemistry

Sodium thiosulfate is also used in analytical chemistry. It can, when heated with a sample containing aluminum cation, produce a white precipitation:

2 Al3+ + 3 S2O32− + 3 H2O →3 SO2 + 3 S + 2 Al(OH)3

Medical

It has also been used as treatment of calciphylaxis in hemodialysis patients with end-stage renal disease.[6]

in foot baths for prophylaxis of ringworm, and as a topical antifungal agent for tinea versicolor.

in measuring the volume of extracellular body fluid and the renal glomerular filtration rate.

Sodium thiosulfate is also used:

As a component in hand warmers and other chemical heating pads that produce heat by exothermic crystallization of a supercooled solution.

In bleach

4 NaClO + Na2S2O3 + 2 NaOH →4 NaCl + 2 Na2SO4 + H2O

To lower chlorine levels in swimming pools and spas following super chlorination.

To remove iodine stains, e.g. after the explosion of nitrogen triiodide.

Similarly, sodium thiosulfate reacts with bromine to render harmless products. Solutions of sodium thiosulfate are commonly used as a precaution in chemistry laboratories when working with bromine.

In bacteriological water assessment.

In the tanning of leather.

S2O32−(aq) →SO32−(aq) + S(s)

As part of patina recipes for copper alloys.

Often used in pharmaceutical preparations as an anionic surfactant to aid in dispersion.

It can also be used as a very interesting solute in supersaturation experiments.

Short Description:

Sodium Thiosulfate used as a Pond / Aquarium Dechlorinator. This product also used as a Photography as a fixing agent (hypo) to dissolve unchanged silver salts from exposed negatives.

Dechlorinating liquid

RXSOL Polyelectrolite is a unique, medium molecular weight, anionic polyelectrolyte designed to be used as a precipitation aid and sludge conditioner for waste water treatment systems.

Application:

APPLICATION & ADVANTAGE :

Immediate flocculation activity.

Non-hazardous to use.

RXSOL Polyelectrolite has been found particularly effective for metal finishing and most industrial thickening and clarification operations as well as metal hydroxide precipitation.

Very economical to use.

RXSOL Polyelectrolite is designed to be used at full strength, eliminating the need to make up stock solutions prior to use, thus completely eliminating the make up difficulties of powders and emulsions. It blends into the waste stream immediately with no undissolved particles, globules or waste.

Effective over a wide pH range.

Works well with other treatment aids.

RXSOL Polyelectrolite concentrated formula is extremely economical to use. One gallon of RXSOL Polyelectrolite will treat up to 100,000 gallons of waste water. It may be injected into a flowing stream, or may be metered into an agitated flocculator tank.

Packing Size:

25.00 Ltr.

Image:

Thumb:

Using Procedure:

RXSOL Polyelectrolite should be metered full strength into the flocculation station of conventional hydroxide precipitation waste water treatment systems. Typical feed rates of RXSOL Polyelectrolite vary from 8 to 12 ppm which is the equivalent to one gallon treating 25,000 to 82,000 gallons of waste water. RXSOL Polyelectrolite works well over a wide pH range with values of 7.5-10.0 being optimum. Uniform agitation is vitally important for optimum contact. Mild agitation by low speed non-shear agitators is recommended. Do not use high speed mixers or pump recirculation for mixing or an agitator speed over 100 RPM. These methods will shear and break up the floc formation. Due to the wide variety of waste water treatment facilities, equipment and waste material to be treated, it is recommended that a water treatment study be performed to assure the most cost effective treatment method available. .

Note:

STORAGE/HANDLING

Store at 40-95° F (5-35° C) for maximum stability. Keep away from heat, sparks and open flame. Do not get in eyes, skin or clothing. Do not take internally. Wear proper protective clothing and face shield. Material spilled on floors is very slippery and most difficult to wash down. Material should be scooped up as much as possible and the remaining thin film adsorbed with absorbent clay or sweeping compound. Refer to the Material Safety Data Sheet for more complete details.

Featured Product :

Featured Product

Short Description:

Anionic polyelectrolyte used in raw water and wastewater treatment

POLYELECTROLYTES

High Molecular weight flocullant polymers available in Anionic, Cationic grades
Description:
High molecular weight flocullants are capable of promoting flocullation by neutralizing the superficial electric charges of sludge particles in the water and unstabilizing each individual particles. The particles then are absorbed by the activated functional group in the flocullant polymer.

Powder Grades :

Anionic Polyelectrolyte
Cationic Polyelectrolyte

Water and Dustproof 10kg Bag

LIQUID Grades :

Anionic Polyelectrolyte
Cationic Polyelectrolyte

(FOOD GRADE SUITABLE FOR DRINKING WATER)
High Density Polyethylene Carboys 50kg Carboy

Waste water treatment chemicals Polyelectrolite

Alias:

Maxtreat 3222, OXYGEN CONTROLER, OXYNON H-171, ST-DOS H-400, CORTROL

Active Matter:

100%

Packing Size:

25.00 Ltr.

Image:

Thumb:

Using Procedure:

Always mix 5006 with fresh DI water or softened water . On complete dissolution of the product 5006 may be mixed with most boiler chemicals used for boiler treatment. Its dosing pumps, piping and valves should be made of stainless steel, polyethylene, or PVC.

Control of Dose:- RXSOL 5006 dose is normally controlled by a RXSOL SULFITE test on the boiler water.

Note:

PACKAGING : also available in a wide range of containers
COMMON NAME : OXYGEN CONTROLER

Storage And Handling: Store in a cool and tight container. For detailed information, consult the material safety data sheet (MSDS).

Packaging: RXSOL 5006 is available in a wide range of containers

Featured Product :

Featured Product

Article News:

Keep your machineries running with Oxygen Scavengers

Seaclean for Soot Cleaning

Oxygen scavengers for Boiler Water

Hydrazine Hydrate exporter

Short Description:

This is most common oxygen scavengers used to effectively remove dissolved OXYGEN from your feedwater.

Other Useful PRODUCT :::

No.	Item	Specification	Function
1	Coagulant	Main Component: Polymerization aluminum chloride Molecular formula: Al2Cl(OH)5 Concentration: 100%	Use to remove suspended matter in raw water
2	Coagulant aid	Main Component: Anionic polyacrylamide (A molecular weight of 15000000 or more) Molecular formula: (C3H5NO)n Concentration: 100%	Use to assist suspended matter removal
3	Oxygen Scavenger	Main Component: Sodium sulfite Molecular formula: NaSO3 Concentration: 90%	Use to remove oxygen from raw water
4	Anti Foam	Main Component: Polyether Concentration: 40%	Use to prevent foam formation
5	Biocide	Main Component: Hypochlorous acid Molecular formula: NaClO Concentration:10-13%	Use to remove microorganisms from raw water
6	Salt	Main Component: Sodium chloride (Non-iodized) Molecular formula: NaCl Concentration:99.5%	Use to soften the resin
7	Ammonia water	Main Component: Ammonium Hydroxide Molecular formula:NH3•H2O Concentration: 27%	Use to adjust PH value of RO water
8	Scaleinhibitor	Main Component: carboxylic acid salt Concentration: 30% Liquid industrial synthetics;	Use to prevent scaling formation

9	Reverse Emulsion Breaker	Main Component: Organic amine Concentration:35%	Use to break oil-water interface
10	Corrosion Inhibitor	Main Component: Phosphonate Concentration:35%	Use to prevent corrosion formation
11	Scaleinhibitor	Main Component: carboxylic acid salt Concentration: 20%	Use to prevent scaling formation
12	Coagulant	Main Component: Polymerization aluminum chloride Molecular formula:Al2Cl(OH)5 Concentration: 100%	Use to remove suspended matter in raw water
13	Coagulant aid	Main Component: Anionic polyacrylamide (A molecular weight of 15000000 or more) Molecular formula: (C3H5NO)n Concentration: 100%	Use to assist suspended matter removal
14	Citric Acid	Main Component: Citric acid Molecular formula: C6H8O7 Concentration: 90%	Use to adjust PH value of gas stripping column prevent scaling formation
15	Biocide	Main Component: quaternary ammonium salt Concentration:40%	Use to remove microorganisms from raw water
16	Oxygen Scavenger	Main Component: Sodium sulfite Molecular formula: NaSO3 Concentration: 90%	Use to remove oxygen from raw water
17	Filter Aid	Main Component: Twelve sodium dodecyl benzene sulfonate Molecular formula: C18H29NaO3S, Concentration: 85%	Use to clean the walnut filter
18	NaOH	Main Component: NaOH Concentration:99%	Use to adjust PH value of treated water prevent corrosion formation

Salt

Main Component: Sodium chloride(Non-iodized)

Molecular formula: NaCl

Concentration:99.5%

Use to IWPS remove microorganisms from raw water

HCL

Main Component: HCL

Concentration: 36%

Use to IWPS adjust water quality

NaOH

Main Component: NaOH

Concentration:33% Liquid

Use to IWPS adjust water quality

Oxygen Binder Sulphite based

Acts as superior quality cleaner/degreaser. It is a new technology surfactant degreaser ( high solvency and emulsification effect ) , Being free from caustic and hydrocarbons it is very gentle on hands & ideal for cleaning walls, wood works, metal and other areas for removal of grease, oil, sludge, carbon deposits, general dirt and grime.

Alias:

Aqua Sol, Aquabreak PX

Active Matter:

63-72

Application:

Can be used for all types of cleaning and degreasing including engine rooms and cargo tanks. Can be used as accoomodation cleaner for Bulkheads, Deck, Toilet etc. Suitable for cleaning of Soiled Textiles such as rugs, cover, mats etc. Effectively Clean Fibre Glass, Boats, Hulls and Painted Surfaces.

NOTE : Bio-degradable product, it is low toxic, non-caustic and from hydrocarbons.

Fields:-
RXSOL-16-3003-020 containing corrosion inhibitors to prevents the corrosion of metals such as Aluminium, Copper, Brass and Tin. RXSOL-16-3003-020 is designed to clean Animal / Vegetables oils, Fats, Hydrocarbon removes Dirt, Iink, Carbonized grease, Oil, Heavy oils etc. Specialized for all types of cleaning and degreasing.may be applied by brush, handspray or used in ultrasonic cleaning tanks, immersion soak tanks and high and low pressure spray appliances. May be used neat or diluted by up to 50 parts of water according to the amount and type of soil to be removed.

Tank Cleaning:-
(Cargo tank cleaning after mineral, animal, vegetable and fish oil. )

Packing Size:

20.00 Ltr.

Image:

Thumb:

Using Procedure:

1st of all by stripping suction removes all possible oil (greasy materials). To prevents evaporation of lighter fraction oil flush the system with cold water.May be brushed on, sprayed (Hand spray/Direct injection) recirculate the system with RXSOL-16-3003-020 Solution

1.	Cleaning with washing machines. Dose rate: 0.3-5 ltr per ton wash water (0.03-0.5%).
2.	Cleaning with recirculation method. Dose rate: 0.5-10 ltr per ton wash water, (0.05-1%).
3.	Spot cleaning. Hand sprayed neat or diluted up to 1-10 parts water and left for about 15-20 minutes before.washing.off.

DOSAGE:-

Nature Of Residue	Hand Spray	Direct Injection	Circulation
Veg.Oil (Drying/Non Drying Fish Oil,Alcohol,Acids,Amines)	1-10%	0.03-0.5%	0.05-0.7 %
ORGANIC MATERIAL (HYDROCARBON)	NA	0.0 5-0.5%	0.05-0.7%

RXSOL-16-3003-020 has numerous general cleaning applications including the removal of greases, oil, sludge, carbon deposits, general dirt and grime. Can be used as engine room cleaner. Suitable for cargo tank cleaning. Can be used as accommodation cleaner for bulkheads, decks, toilets. Suitable for cleaning of soiled textiles as rugs, covers, mats, overalls, etc. Effectively cleans glass fibre boats, hulls and painted surfaces

Note:

WHY RXSOL-16-3003-020 is better ?

An economical highly concentrated product.

Compatible with oily water separators.

Releasing the oil phase for reclamation.

Suitable for all types of floors. Deodorizing nature.

Eliminates the need to buy & stock duplicate products because of its effectiveness.

Also used for gas and hydrocarbon freeing of tanks. Free from caustic & hydrcarbon, Non flammable Water based, Biodegradable. Safe to metal

Featured Product :

Featured Product

Video Links:

Aqua Break

Short Description:

Concentrated cleaning agent based on nonionic detergents, alkaline components, special components to stabilise the hardness and corrosion inhibitors for aluminium.

Information:

Aqubreak is classified as one of versatile cleaner which is free from caustic and solvent. Good Blend of surfactant makes easy OIL EMULSIFYING properties. Easily availabe at all Indian and Middle East port.

Degreasing Agent, Non Caustic Cleaner, aquabreak px msds, marine universal cleaner

aquatuff

enviroclean

PX, Aquabreak, Cleaning Agent, Water Based Degreaser

Ship galleys decks cleaning agent. Best Oil cleaning action in Engine room, Helpfull for cargo tank cleaning. Also can be utilized as multipurpose cleaning agent for soiled textiles as rugs, covers, mats, overalls etc. Also effectively cleans boats, machinery parts, fibreglass area.

Aquabreak available in various packing size for making smooth supply in Mumbai, JNPT, GOA, Manglore, Kandla - Gandhidham, Chennai - Ennore, Vizag _ Viakhapatnam, Gangavaram, Kakinada, Kolkata, Haldia, Middle East, Dubai, Fujairah, Sharjah

Best classified cleaner for Shiping Industries, Oil and Rigs, Railway, Petroleum Industries. Multi-purpose utility of Aqua Break Eliminates the need to buy & stock duplicate products because of its effectiveness.

Also refer this link :::

Aqua Break RX 20 Ltr - Concentrated cleaning agent based on nonionic detergents, alkaline components, special components to stabilise the hardness and corrosion inhibitors for aluminium.RXSOL-16-3003-020

Aqua Break RX 25 Ltrs - New technology surfactant degreaser for removal of grease, oil, sludge, carbon deposits, general dirt and grime. designed to clean Animal / Vegetables oils, Fats, Hydrocarbon removes Dirt, Iink, Carbonized grease, Oil, Heavy oils etc.RXSOL-16-3003-025

Aqua Break RX 210 Ltrs - Specialized for all types of cleaning and degreasing. Effective to clean Animal / Vegetable oils, Fats, Hydrocarbon removes Dirt, Iink, Carbonized grease, Oil, Heavy oils etc. Effectively Clean Fibre Glass, Boats, Hulls and Painted Surfaces.RXSOL-16-3003-210

Aqua Break RX HD 20 Ltr - Numerous general cleaning applications including the remover of grease, oil, sludge, carbon deposits, general dirt and grimeRXSOL-20-3017-020

Aqua Break RX HD 25 Ltr - Advanced degreaser for engine rooms and cargo tanks it can be used for all types of cleaning and degreasing including engine rooms and cargo tanks. Can be used as an accommodation cleaner for bulkheads, deck, toilet etc. Suitable for cleaning of soiled textiles such as rugs, cover, mats etc. EffectivelyRXSOL-20-3017-025

Aqua Break RX HD 210 Ltr - Cargo tank cleaning after mineral, animal, vegetable and fish oil, Effective grease cleaner and free from caustic and hydrocarbonsRXSOL-20-3017-210

Degreaser cum oil water separator

Its wide range of usage is in water treatment, because it can act as an coagulant, flocculant, precipitant and emulsion breaker. As coagulant and flocculant, aluminum sulfate successfully removes turbidity, suspended solids and colloidal color,reduces biochemical oxygen demand (BOD) and extremely clarifies potable, process and wastewaters.

Alias:

ALUM

Application:

Also used as foam fire extinguisher

Aluminium sulfate reacts with sodium bicarbonate to which foam stabilizer has been added, producing carbon dioxide for fire extinguishing foam.

Al2(SO4)3 + 6 NaHCO3 → 3 Na2SO4 + 2 Al(OH)3 + 6 CO2

The carbon dioxide is trapped by the foam stabilizer and creates a thick foam which will float on top of hydrocarbon fuels and seal off access to atmospheric oxygen, smothering the fire. Chemical foam was unsuitable for use on polar solvents such as alcohol, as the fuel would mix with and break down the foam blanket. The carbon dioxide generated also served to propel the foam out of the container, be it a portable fire extinguisher or fixed installation using hoselines. Chemical foam is considered obsolete in the United States and has been replaced by synthetic mechanical foams, such as AFFF which have a longer shelf life, are more effective, and more versatile, although some countries such as Japan and India continue to use it.

In the construction industry, it is used as waterproofing agent and accelerator in concrete.

Packing Size:

20.00 Slab Kg

Image:

Thumb:

Using Procedure:

- For the production of Aluminum salts, Soaps and Aluminum Hydroxide Gel. - As a Catalyst in Ethane Production.
- Textile industry.
- Paper production.

- For the production of Glycerin
- As a Foaming Agent in Fiber Foams.
- As a Clearing Agent for Fats and Foams. - In sugar industry.

Note:

properties :::---

1. Properties: Including anhydrous and hydrous(18 crystal water) type. Usually, the crystal separated out from aqueous solution at the normal temperature is A12(SO4) 3.18H2O; When weathering, the average molecular structure is A12(SO4) 3.14H2O, may appear white powdery, with bright flake or crystalline flakelet, odorless, to change the taste from sweetness to slight astringency.

2. Uses: Solidifying agent ( to purify grease and water ) and stabilizer in pasteurization of albumin ( including: liquid or refrigerated whole egg, egg white or egg yolk ), the maximum allowable use level ( FAO/WHO.1984 ) is 0.036%.

3. Standard: HG2225-2001

4. State: Flake or powder

5. Packing: 25/50 kg/bag, 25MT/20'FCL

Related Products:

Drinking Water Additive

Flocculant (Anionic Polymer) DAF

Flocculant (Cationic Polymer) DAF

Flocculating Agents

EWT Coagulant

Featured Product :

Featured Product

Short Description:

it can act as an coagulant, flocculant, precipitant and emulsion breaker. As coagulant and flocculant, aluminum sulfate successfully removes turbidity, suspended solids and colloidal color,reduces biochemical oxygen demand (BOD) and extremely clarifies po

Information:

Aluminium Sulfate is one of popular water treatment chemicals. We are one of popular high purity Alum - Fitkarin manufacturer, Supplier and exporter in India. We are keeping ready stock of materials in our Mumbai, Gandhidham, Surat, Kolkata, Chennai - Ennore, Visakhapatnam, Fujairah - Dubai

ALUMINUM SULFATE, Aluminium sulfate, Dialuminum trisulfate, 10043-01-3, Aluminum sulfate (2:3), Filter Alum, Aluminum sulphate, Aluminium sulphate, Dialuminum sulfate, Papermaker's Alum Sulfuric acid, aluminum salt (3:2), Aluminum alum, Pickle Alum, Pearl Alum, Dialuminum sulphate

Cake alum (VAN), Aluminum sesquisulfate, Aluminum alum (VAN), Hi Soft C 2, Aluminum(III) silfate, Caswell No. 031A, Nalco 7530, Tai-Ace S 100

Tai-Ace S 150, Aluminum sulfate anhydrous, Aluminum sulfate (3:2), Sulfuric acid, aluminum salt, Sulphuric acid, aluminium salt, CCRIS 9170, UNII-I7T908772F, alum, aluminum hydrogen sulfate, aluminum potassium sulfate, aluminum sulfate, potassium aluminum sulfate

Aluminum Alum;. Aluminum sulfate anhydrous; Aluminum trisulfate anhydrous; Cake Alum; Dialuminum sulfate; Sulfuric acid aluminum salt (3:2); Aluminiumsulfat (German); Sulfato de aluminio (Spanish); Sulfate d'aluminium (French); Aluminum sesquisulfate

Aluminum sulfate is a water-soluble white crystalline solid compound with the chemical formula Al2(SO4)3. Aluminium Sulfate is a coagulating agent in the purification of drinking water and wastewater treatment plants, pH regulation of garden soil, and other commercial or industrial applications like paper manufacturing, in firefighting foams, and in sewage treatment and water purification.

Aluminum Sulfate Anhydrous is an aluminium salt adsorbs and precipitates protein antigens in solution.It is primarily used as a coagulating agent in minor cuts and abrasions.

Aluminium sulfate, Al2(SO4)3, is widely used by wastewater treatment plant as a flocculating agent and in the drinking water for purification. And in industry, Its most common applications are in the pulp and paper industry.

How Aluminium Sulfate works as a water purifier and discolouring agent?

Aluminium sulfate has highly charged cation of Al3+ which is powerfully attracting Negative particles from any solution such as those which discolour our raw water supplies, are attracted to this cation, react with it and then precipitate out of solution as ionic solids.

Mumbai, Kandla, Chennai Ennore, Visakhapatnam, Kolkata, Fujairah - Dubai

Aluminium Sulfate is used as coagulant to remove almost any kind of impurities in water. Its main function is to provide electrically charged ions capable to neutralize effectively the electric charges of the colloid material present in the water, thus allowing them to come together. The alum reacts rapidly with the water alkalinities. This produces a gelatinous precipitate of aluminum hydroxide that entraps and absorbs impurities.

Our other chemicals are as follows:

SULPHATES

Aluminium Sulphate Non Ferric
Ammonium Sulphate
Copper Sulphate
Ferrous Sulphate
Magnesium Sulphate
Manganese Sulphate
Potassium Sulphate
Sodium Sulphate
Sodium Thiosulphate
Zinc Sulphate Heptahydrate
Zinc Sulphate Monohydrate

BY PRODUCTS

Acetic Acid
Ammonium Sulphate
Copper Hydroxide
Copper Sulphate
EDTA Di Sodium
KCl + K2SO4
Magnesium Hydroxide
Manganese Dioxide
Phosphoric Acid
Poly Aluminium Chloride
Potassium Chloride
Potassium Sulphate
Sodium Hypo Chlorite
Sodium Per Carbonate
Sodium Sulphate
Sodium Sulphite
Zinc Sulphate
Zinc Oxide

DETERGENT CHEMICALS

Acid Slurry
AOS
Caustic Soda Flakes
Soda Ash
Sodium Bi Carbonate
Sodium Sulphite
STPP

SULPHITES

Sodium Sulphite
Sodium Bi Sulphite
Sodium Meta Bi Sulphite

PHOSPHATES

Di Sodium Phosphate
Di Calcium Phosphate
Sodium Tri Poly Phosphate
Di Ammonium Phosphate

TEXTILE CHEMICALS

Acetic Acid
Citric Acid
Hydrogen Peroxide
Potassium Carbonate
Sodium Acetate

CHLORIDES

Potassium Chloride
Sodium Chloride
Magnesium Chloride
Calcium Chloride

NITRATE

Potassium Nitrate
Calcium Nitrate
Sodium Nitrate

WATER SOLUBLE FERTILIZERS
Boron - 10% & Boron - 20%
Humic Acid
Potassium Humate
Ammino Acid
Mix Micronutrients
Sulphur WDG

OTHER

T.G. Urea
Citric Acid
Phosphoric Acid
Copper Acetate
Cobalt Sulphate
Nickel Sulphate
Chromium Chloride
Magnesium Oxide
Cupric Chloride
Nickel Carbonate
Copper Carbonate
Sodium Nitrite

Alum - Fitkari Slab

Antifoam Defoamer

Sodium Thiosulphate Solution

Air Cooler Cleaner Sea Water SIDE 25 Ltr

RXSOL 2000 corrosion inhibitor

Rocor NB Liq Corrosion Scale Inhibitor

Demineralised Water

One Shot Universal Liquitreat 100 25 Ltrs

Hardness Control Liquid

AQUA Tuff High Foam conc.

RXSOL RO - 3

Bentonite Powder

Poly Aluminium Chloride 25Ltr Liq.

Poly Aluminium Chloride 25 Kg. PWD

Hydrogen Peroxide 6% Solution

Delta Marine And Offshore Services

Sodium Thiosulphate Solution

Polyelectrolyte

Oxygen Scavanger

Aqua Break RX 20 Ltr

ALUMINIUM SULFATE